In a redundant joint model, three bar members are pin connected at Q as shown in the figure. Under some load placed at Q, the elongation of the members MQ and OQ are found to be 48 mm and 35 mm respectively. Then the horizontal displacement u and the vertical displacement v of the node Q, in mm, will be respectively, M MN = 400 mm NO = 500 mm NQ = 600 mm %3D X,u

In a redundant joint model, three bar members are pin connected at Q as shown in the figure. Under some load placed at Q, the elongation of the members MQ and OQ are found to be 48 mm and 35 mm respectively. Then the horizontal displacement u and the vertical displacement v of the node Q, in mm, will be respectively, M MN = 400 mm NO = 500 mm NQ = 600 mm %3D X,u

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C - Counterclockwise Rotation of a Stress Element Figure 5 of 6 The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5) where the magnitudes of the stresses are |0z| = 13 ksi, Joy = 23 ksi, and |Tzy| = 12 ksi. Determine the state of stress on an element rotated 45° counterclockwise from the element shown. Express your answers, separated by commas, to three significant figures. • View Available Hint(s) Vol AEO I vec Or =, oy =, Tự'y = ksi, ksi, ksi Submit Pearson
0.01 in. - Undeformed Deformed 0.10 in. 0.004 in. FIG. P2.39 0.12 in.
Question 2 (Part1-2): Consider the same truss again here as shown below with the following connectivity table. Suppose that the origin of the coordinate system is fixed at node 1. Fina the values of cos(0) for each element. What is the summation of of I for all three elements. (Hint: find 1+l2 + l3). 100 mm (1) (2) (3) 150 mm 200 mm Elements Node (i) Node () (1) (2) (3) 3. 4 100mm 22
85 In a pure shear condition, the maximum value of shear stress is observed to be 20 MPa for an element shown, subjected to above condition. The change in length of diagonal AB is μm. [Take G = 80 GPa] [Correct upto 2 decimal places] D 10 cm A 10 cm B () C
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 120 in. Rod (1) has a length of L1 = 87 in. and a cross-sectional area of A1 = 0.65 in.2. Rod (2) has a length of L2 = 84 in. and a cross-sectional area of A2 = 1.15 in.2. Rigid bar ABC is to remain horizontal under a load of P = 25 kips. Determine the distance x (in inches rounded to the nearest tenths) from joint A to the location of load P so that bar ABC remains horizontal.
NOTE: PLEASE SOLVE THIS QUESTION WİTH FINITE ELEMENT METHOD...solve 20 mins asap hand written
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.19 in. In segment (2), the normal strain is measured as 1,650 pin./in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. Answers: (a) 8₂ = (b) E₁ = 41 in. (2) 93 in. lin. uin./in. P
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
For the truss shown in the following figure, the temperature of member BC is raised by 110 °C, and member BD is raised by 70 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: b) Ay = c) B₂ A | C ΤΙΣ Part 1. Calculate the displacements at the joints: a) Az = d) By = e) C₂ mm mm mm mm mm Part 2. Calculate the force in each member: a) NAB = b) NAC = c) NBD = d) NBC = e) Ncp = f) NAD = 5 m N N N N N N B D 5 m
The length of a plane truss member is 2.5m. What will be the stiffness matrix coefficient k₁1 for this truss? Consider E= 210 GPa and area of cross section is 150 mm².