In a parallel flow heat exchanger, hot fluid enters the heat exchanger at a temperature of 150°C and a mass flow rate of 3 kg/s. The cooling medium enters the heat exchanger at a temperature of 30°C with a mass flow rate of 0.5 kg/s and leaves at a temperature of 70°C. The specific heat capacities of the hot and cold fluids are 1150 J/kg-K and 4180 J/kg-K, respectively. The convection heat transfer coefficient on the inner and outer side of the tube is 300 W/m?.K and 800 W/m².K, respectively. For a fouling factor of 0.0003 m².K/W on the tube side and 0.0001 m².K/W on the shell side, determine the overall heat transfer coefficient, the exit temperature of the hot fluid as well as the surface area of the heat exchanger.

In a parallel flow heat exchanger, hot fluid enters the heat exchanger at a temperature of 150°C and a mass flow rate of 3 kg/s. The cooling medium enters the heat exchanger at a temperature of 30°C with a mass flow rate of 0.5 kg/s and leaves at a temperature of 70°C. The specific heat capacities of the hot and cold fluids are 1150 J/kg-K and 4180 J/kg-K, respectively. The convection heat transfer coefficient on the inner and outer side of the tube is 300 W/m?.K and 800 W/m².K, respectively. For a fouling factor of 0.0003 m².K/W on the tube side and 0.0001 m².K/W on the shell side, determine the overall heat transfer coefficient, the exit temperature of the hot fluid as well as the surface area of the heat exchanger.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

13 - A fixed volume insulated tank, which was initially empty, was connected by a valve to a distribution line carrying helium gas at a temperature of 125ºC. The valve is opened first and closed when the pressure is the same as the distribution line pressure. What is the final internal energy of helium in the tank? (Internal energy of the warehouse in the final state = Enthalpy of the distribution line). (Cp=5.1926) will be taken. a) 701.0 kJ/kg B) 649.1 kJ/kg NS) 2014.7 kJ/kg D) 2118.6 kJ/kg TO) 2066.7 kJ/kg
E. Draw a heat transfer diagram showing the heat flow (where q is going) when you use an ice pack on an injury versus a heat transfer diagram showing the heat flow when you use a heat pack on an injury. Treat the ice or heat pack as the system.
I need the answer at 20 minute
A refrigerant 134a of a vapor compression refrigeration system includes a liquid-suction heat exchanger. The heat exchanger cools saturated liquid coming from the condenser from 45 °C to 37 °C with the saturated vapor which comes from the evaporator at -8 °C. Calculate: a.) The COP of the system without heat exchanger. b.) The COP of the system with the heat exchanger. c.) Find the percent increase of performance of the system with the heat exchanger based on the system without heat exchanger. d.) Draw the schematic and P-h diagram of the two set-up.
The Electric hand dryer is an example of........ loop system
The density of a fluid decreases as it passes through a pipe of constant diameter. The mass flow rate of the outlet stream is ____________ the mass flow rate of the inlet stream. a. less than b. equal to c. greater than
I need the complete solution and all the process
3.24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)
7
Figure P.16.10 shows a plane truss pinned to a rigid foundation. All members have the same Young's modulus of 70 000 N/mm² and the same cross-sectional area, A, except the member 12 whose cross-sectional area is 1.414A. Under some systems of loading, member 14 carries a tensile stress of 0.7 N/mm². Calculate the change in temperature which, if applied to member 14 only, would reduce the stress in that member to zero. The coefficient of linear expansion a=24x10-/º C. Ans. 5.5°.
PROPERTIES OF MOIST AIR / SENSIBLE HEATING / SENSIBLE COOLING
e) Draw diagram of ‘regeneration cycle’ and state the advantages and disadvantages of regeneration.