24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)

24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air cooled refrigerant condenser (similar to the ones used for home air conditioners) is shown, The system condenses 0.1 kg/sec of 60 C R134A refrigerant. Air temperature rises by 5 C passing over the coils. Calculate the mass flow rate of air pushed through the condenser.
Thermodynamics: A refrigeration unit using Refrigerant-134a is used to maintain a certain space at –15°C. The condenser rejects heat (?H) to cooling water that enters the condenser at 15°C at a rate of 0.2 kg/s and leaves at 35°C (all as saturated liquid water). The superheated refrigerant enters the condenser at 0.8 MPa and 40°C and leaves as a saturated liquid at the same temperature. If the compressor consumes 4.5 kW of power, determine (a) the mass flow rate of the refrigerant, (b) the refrigeration load (?̇L), (c) the COP.
* İl. Gmail ► Untitled docu.. A system consists of a turbine and heat exchanger are connected in series. The working fluid is entering the turbine at P1 0.6 Mpa, T= 200 °C and leaving it with P,= 0.2Mpa. Then the turbine exit becomes the heat exchanger inlet to increase the fluid temperature to become 800 °C. Considering that the adiabatic power y =1.4 and the specific heat = 1.005 KJ/Kg.K. Determine the turbine production work WT and heat exchanger energy needed to be added quE. T = 200 °C P,= 0.6 Mpa- T T2 ? P,=0.2 Mpa h high НЕ T= 800 °C P3 =? 9 in
In the evaporator of an air conditioning system, air flows over finned tubes through with the refrigerant R134a flows. air out refrigerant in refrigerant out air in The mass flow rate of the air is 0.75 kg/s and the air enters at 40°C and pressure 1.04 bar. The air leaves the evaporator at 25°C and 1.01 bar. The refrigerant enters the evaporator with a quality of 0.2 and a temperature of 12°C. The refrigerant exits as saturated vapor. Obtain the properties of air and R134a using the fluids "Air" and "R134a" in EES. What is the volumetric flow rate of the air entering the heat exchanger (m^3/s)? Determine the rate of heat transfer from the air to the refrigerant (W). Determine the mass flow rate of the refrigerant (kg/s).
An air-conditioning absorption system has an evaporator capacity of 350 kW with a COP of 0.90 operating at a temperature of 25 C with a condensing temperature of 35 C. The same cooling tower was used to reject the heat from the condenser and the absorber operating 45 C & providing 1 kg/s of water plus lithium bromide solution to the generator. Consider the heat rejection ratio of condenser to evaporator is 1.05, Determine the following: 1. Heat given by the generator & the size of condenser in kW 2. Leaving condenser & evaporator enthalpies & the mass of refrigerant water flowing from the generator to the condenser then to the evaporator & to the absorber (using evaporator heat balance). 3. Weight of lithium bromide in kg/s, concentration in percent & enthalpy from the absorber to the generator in kJ/kg 4. Enthalpy from the generator to condenser in kJ/kg (using condenser heat balance) & concentration in percent & enthalpy from generator to absorber…
2. A surface condenser serving a 50,000-kW steam-turbo generator unit receives exhaust steam at the rate of 200,000 kg/hr. Vacuum in condenser is 0.88025 bar. Sea water for cooling enters at 27°C and leaves at 40°C. For steam turbine condenser as heat given up to cooling water. Calculate the LMTD.
2-) 10500 kg/hr of water is heated using a counter-flow, double-pipe heat exchanger utilizing superheated steam. Steam passes through the heat exchanger at 130 °C after entering at 180 °C. Water has an entrance temperature of 30 °C and an outlet temperature of 80 °C. Calculate the heat transfer area if the overall heat transfer coefficient from steam to water is 814 W/m² K. How much more area would there be if the fluid flow was parallel?
Q.13 A vapour compression refrigeration system using refrigerant F-12 is employed to produce 8640 kg of ice per day. The condensing and evaporating temperature of refrigcrant are 48°C and-20°C respectively. Saturated liquid leaves the condenser and saturated vapour leaves the evaporator. Compression is isentropic, water at 35°C is used to form the ice. The temperature of ice should be-8°C. Heat flow into the brine tank from surroundings may be taken as 10% of total heat absorbed from water to form ice. Determine the power required to drive the compressor. Take specific heat of ice 2.26 kJ/kg-K. Latent heat of ice = 335 kJ/kg. Specific heat of water = 4.2 kJ/kg-K. The following data may be used: %3D Temp. Pressure Enthalpy Entropy °C bar kJ/lg kJ/kg-K Liquid Vapour Liquid Vapour 48°C 11.64 82.83 205.83 0.2973 0.6802 -20 1.51 17.82 178.74 0.0731 0.7087 Specific heat of vapour 0.82 kJ/kg %3D
B- A steam generation unit in power plant operates at a constant pressure of (10 bar) and the water evaporates at the rate of (0.9 from the total mass flow rate of water). Inlet and leaving water enthalpy are (200 kJ/kg) and (2000 kJ/kg) respectively. The inlet and outlet velocity are (10 m/s) and (25 m/s) respectively. If 80% of the heat energy supplied to the steam generation unit is used in evaporating the fluid. Determine the heat evaporation and work done if the inlet and outlet diameter are the same level. The fuel produces 28000 kJ of heat energy for one kg and the mass flow rate of water is 1000 kg/h.
ercise 6 6.1 A surface condenser is fitted with separate air and condensate outlets. A portion of the cooling surface is screened from the incoming steam and the air is passes over these screened tubes to the air extraction and becomes cooled below the condensate temperature. The condenser receives 20 000kg/hr of dry saturated steam at 36.2°C. At the condensate outlet the temperature is 34.6°C TK and at the air extraction the temperature is 29°C. The volume of air and vapour leaving the condenser is 3.8m3/min. Assume constant pressure throughout the condenser, calculate: 6.1.1 the mass of air removed per 10 000kg of steam (2.63kg); 6.1.2 the mass of steam condensed in the air cooler per minute (0.5kg/min)%3B 6.1.3 the heat rejected to the cooling water (13451kW).
A counterflow heat exchanger operates with hot liquid entering at 200° C and leaving at 160°C. The liquid to be heated enters at 40°C and leaves at 140°C. What is the log mean temperature difference between the hot and cold liquids?
3.36 Both C's in a parallel-flow heat exchanger are equal to 156 W/K, U 327 W/m²K and A = 2 m². The hot fluid enters at 140°C and leaves at 90°C. The cold fluid enters at 40°C. If both C's are halved, what will be the exit temperature of the hot fluid?