In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass of the car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What input force (in N) is needed to support the car and the output plunger when the bottom surfaces are at the same level?

In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass of the car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What input force (in N) is needed to support the car and the output plunger when the bottom surfaces are at the same level?

Name: QUESTION 10In a hydraulic car lift, the input piston has a radius of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 10In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass ofthe car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What inpu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

right cylindrical object has a diameter of 1526 mm and a height of 2.1m. The density of water is 1000 kg/m3. If the right cylindrical object is placed in the water, what is the buoyant force?
A person wearing long snowshoes can walk across a blanket of freshly fallen snow without sinking far into the snow because (p.s. Google snowshoe if you don't know how one looks like) snowshoes cover a larger area than a foot and so the pressure is reduced. the snowshoes reduce the force of the person on the snow. the large area of the snowshoe concentrates the force of the person to a point smaller than the foot. snowshoes push less dense snow out of the way so the person stands on more solid ice below
A bicycle tire pump has a piston with area 0.44 inches squared. If a person exerts a force of 30 lb on the piston while inflating the tire, what pressure does this produce on the air in the pump? Give your answer in psi.
Consider a 6-m-long, 6-m-wide, and 2.3-m-high above-ground swimming pool that is filled with water to the rim. Determine the distance (m), Yp, of the line of action of the resultant force from the top of the pool.
The figure below shows a container filled with a liquid of density p up to a height of 4R. The container is of unit width into the plane of the screen and AB is half a parabola with a height of kR and a base of R. Determine the magnitude and direction of the vertical component Fy of the hydrostatic force acting on the curved surface AB if k = 2, R = 0.5 m, p = 1000 kg/m³ and the gravitational acceleration g = 9.81 m/s². Note that Fy is positive if it acts upwards and is negative if it acts downwards. Geometric properties of a half-parabola are also given below. Fy= 1. [-6.7362, -6.3438 kN. 4R h ထမ 35 b Liquid Р X Half-Parabola BR KR A = 3bh 1xc=²bh³ |yxc=hb³ |yy,c=²7/531 2 h63
The 2-m wide gate ab depicted on the right retains water 3 m deep. Determine the horizontal and vertical forces on the gate, then calculate magnitude and direction of the resultant force on the gate.
A full cylindrical tank having a diameter equal to its height contains water with a total mass of 545 lbm. Estimate the radius of the tank.
at the bottom of a container, which forms an angle A with the horizontal, is a cube of edge a, as shown in the figure, made of a material of density p. Determine the force with which the cube presses on the bottom, if a liquid of density p0 is poured into the container. The top edge of the cube is h from the surface of the liquid. There is no liquid between the bottom of the container and the cube. The atmospheric pressure is P and the acceleration of gravity g (neglect the thrust).
Consider two tanks filled with water. The first tank is 8 m high and is stationary, while the second tank is 2 m high and is moving upward with an acceleration of 5 m/s^2. Calculate the pressure of each tank at the bottom.
The plastic block shown below measures l.5 m x/.S m x(.7 m and has a specific gravity of 0.38. The concrete block B (density = 2400 kg/m) is suspended from the corner of the plastic block by means of a cable and the plastic block is thus floating in the lake (T = 15°C) in the orientation shown. Determine the volume of the concrete block (units of liters) noting that it does not rest on the bottom of the lake, Neglect the weight and volume of the cable in your analysis. %3D %3D 1.7 m 0.5m Water Cable B
. A cannister contains water with a height level of 80 cm and is transported up a building using a pulley-operated dumbwaiter. Determine the pressure at the bottom of the cannister when the dumbwaiter is stationary, moving up with an acceleration of 3.8 m/s², and moving down with a downward acceleration of 3.5 m/s². Draw your schematic/ free-body diagram.
A rigid tank filled with oil has two cylindrical tubes with leak-proof pistons fitted in them as shown. When a force of 300 N is applied to piston 1 whose area is 30 cm^2, calculate the maximum weight W that piston 2 of area 300 cm^2 can support.