In a free vortex, the velocity, at point A at a radius of 0.125 m, is measured to be 2 m/s. What will be the difference in height between the point A, and Point B, if point B is a at a radius of 0.231 m What will be the difference in height between the point A, and the surface of the water at the edge of the tank, if the tank is assumed to be very large

In a free vortex, the velocity, at point A at a radius of 0.125 m, is measured to be 2 m/s. What will be the difference in height between the point A, and Point B, if point B is a at a radius of 0.231 m What will be the difference in height between the point A, and the surface of the water at the edge of the tank, if the tank is assumed to be very large

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Create a compilation of the important constants and formulas in Fluid Mechanics. you may also include some diagrams if necessary. Topic's to cover: Fluid Properties (Density to Capillarity) Fluid Statics (Pressure to Hydrostatic Forces) Fluid Dynamics (Continuity Flow, Bernoulli's Equation, Reynolds Number, Orifice, etc.)
fluid mechanics subject! please help ne solve this in details!
3. A cylinder of radius r; rotates at a speed w coaxially inside a fixed cylinder of radius r,. A viscous Newtonian fluid fills the space between the cylinders. a) Determine the velocity profile in the space between the cylinders b) Determine the shear stress on the surface of each cylinder. Are the shear stresses equal? Explain. c) Assume that the fluid is glycerin at room temperature. The cylinders are 25 cm tall, r; = 9 cm, cylinder at one full rotation every 10s. and 10 cm. Calculate the torque required to steadily turn the inner %D
The Colburn equation for heat transfer is: 2/3 0.023 0.2 DG F';u is viscosity, lb h ft; k is thermal conductivity, where C, is heat capacity, Btu lb Btu h ft2 (°F ft); D is pipe diameter, ft; and G is mass velocity per unit area, lb h' ft. The Colburn equation is dimensionally consistent. What are the units and dimensions of the heat transfer coefficient, h?- -1
Oil flows between two parallel plates (Fig. 8.3), one of which is at rest and the other moves with a velocity U. If the pressure is decreasing in the direction of the flow at a rate of 0.10 lbf/ft² per/foot, the dynamic viscosity is 10-31bf-sec/ft2, the spacing of the plates is 2 in. and the volumetric flow per unit width is 0.15 ft2/sec, what is the velocity U?
Fluid mechanics question Can you give a problem with solution about specific volume property
Fluid Mechanics question
2. 21 If there are n variables in a particular flow situation, and these variables contain in primary dimensions, the number of dimensionless groups relating the variables will be (a) n+m (b) n-m (c) m (d)
question is image
sF.r.cylinder.rsh Tcy are the radius of shaft and inside radius of cylinder a P2.11 Consider a concentric shaft fixed axially and rotated inside <( cylinder.r3h.ľcy are the radius of shaft and inside radius of cylinder respectively, with total length L. Let the rotational rate @ rad/s and applied torque be M .Using these parameters, a) Derive a theoretical relation for the viscosity u of the fluid between the shaft and cylinder. b) For a shaft of 8cm long, rotating at 1200 rev./min, with rsh = 2.00 cm and the measured torque is M viscosity? [µ = M(rcy=r sh)/(2nwr;,L)] %3D - 0.293 N.m. What is the fluid [µ=0.29 kg/m.s] rey:205 ( Cos o 6243.
Give 5 applications of Mechanics to our daily life. Similarly, give the principle being applied.
In Fig. both fluids are at 20 ° C. If surface tensioneffects are negligible, what is the density of the oil,in kg/m 3 ?