In a condenser, saturated water vapour flows through cool water pipes, condenses on the surface of the cooling pipes and leaves the condenser as saturated liquid. Cooling water enters the 4-cm-diameter thin copper tubes at an average velocity of 3m/s and at 10°C, and leaves the condenser at 25°C. Saturated vapour at the inlet is at 80°C. What is the mass flow rate of the saturated vapour?

In a condenser, saturated water vapour flows through cool water pipes, condenses on the surface of the cooling pipes and leaves the condenser as saturated liquid. Cooling water enters the 4-cm-diameter thin copper tubes at an average velocity of 3m/s and at 10°C, and leaves the condenser at 25°C. Saturated vapour at the inlet is at 80°C. What is the mass flow rate of the saturated vapour?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A heat exchanger is being used to transfer heat between water and a benzene. The benzene enters the heat exchanger at 1.2 m3/h with a temperature of 90 C. The water enters the heat exchanger at 1 m3/h at a temperature of 15°C. The UA product of the heat exchanger is found to be 2800 kJ/h-°K. . Determine (a) the outlet temperature of water and benzene (b) the heat transfer rate between the fluids for a counter-flow heat exchanger.
Steam (water vapor) enters a stainless steel tube with inner diameter 4cm at 300°C and 60 bar absolute pressure, with a velocity of 8.00 m/s. The steam exits the tube at 300°C and 40 bar absolute pressure. a. Assuming the water vapor behaves as an ideal gas, calculate the steam mass flow rate and the change in kinetic energy (in Watts). b. Using the specific volume values from table B.7, calculate the steam mass flow rate and the change in kinetic energy (in Watts).
air is flowing inside of a pipe with radius=0.4 meters at a mass velocity of 29.4 kg/s*m2 at 322 K, with the walls of the pipe at 300 K. At the conditions of the experiment, the viscosity of air is 1.984 x 10-5 Pa*s, the density of air is 1.22 kg/m3, the heat capacity is 1 kJ/kg*K, and the thermal conductivity is 0.025 W/m*K. Determine the rate of heat loss by air per meter of duct.
the question below is already answered in the photos that I provided I only want to ask how did it find the answersSaturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.my question here is:regarding of the solution pls elaborate how did it get w1 and h1 is it given in the psychrometric chart or it has a specific solution to follow
Air at 1 atmosphere and a temperature of 60 F enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 F by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long. Find also the Q
The remaining wet steam exits the turbine at 11.5 kPa with a quality of 0.88. Determine the minimum pipe diameters required to restrict the maximum inlet velocity to 50 m/s, the maximum extraction velocities each to 75 m/s, and the turbine outlet velocity to 130 m/s. Consider a steam turbine in which steam enters at 10.45 MPa and 780 K with a flow rate of 38.739 kg/s. As shown in the sketch, a portion of the steam is extracted from the turbine after partial expansion at three different locations. The extracted steam is then led to various heat exchangers. The mass flow rates and the temperatures and pressures at each extraction point are given in the following table: Inlet Steam turbine Extraction Location rin(kg/s) P (MPa) T(K) 1 23 4.343 3.054 620 4.345 0.332 482 Extraction 3. 2.871 0.136 x= 0.949 locations Exit 123
The oil (cp = 1 795 W-s/kg-K) from an oil-cooled electric transformer is cooled from 79.4 oC to 29.4 oC at the rate of 1 360.5 kg/h. This is done in an oil-water het exchanger that receives 2 948 kg/h of water at 15.6 Celsius. For the exchanger, U = 295 W/m2-K. Find the exit water temperature and heating area required (a) for counter flow and (b) for parallel flow.
Dry saturated steam at 8 bar expands in a convergent nozzle to a pressure of 0.5 bar and 0.8 dryness fraction. Determine the exit velocity of the steam if the initial velocity of the stream is 125m/s
Consider a pipe with a length of 25 m and diameter of 5 cm. The surface temperature of the pipe is constant at 150°C.Oil at 20°C is passing though this pipe with a mass flow rate of 0.5 kg/s. determine (a) the temperature of the oil at the exit and (b) the total heat transfer rate. Note. Report your solution step by step and clearly.
A pump increases the water presssure from 8kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degrees celsius through a 1.145-cm-diameter opening and exits through a 2.821-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.354kg/s. The specific volume of incoming water is 1.547x10-3m3/kg.
Determine the mass flow rate (kg/s) of water that must flow through a conduit to carry 15,000 kJ/s of heat energy if the temperature difference is 10 degrees Celsius. Cp water=4.186 k*J/Kg*K