In a cold storage plant, it is desired to determine whether to use insulation two inches thick or three inches thick in insulating the walls of the cold storage ware house. Heat absorb through the walls without insulation would cost P96.00 per year per square meter. A two-inch insulation will cost P30.40 per square meter and will cut out 89% of the loss. A three-inch insulation will cut out 92% of the loss and will cost P65.00 per square meter. Using a life 15 years for the insulation with no salvage value and a minimum attractive return of 8%, what thickness of insulation should be used?

In a cold storage plant, it is desired to determine whether to use insulation two inches thick or three inches thick in insulating the walls of the cold storage ware house. Heat absorb through the walls without insulation would cost P96.00 per year per square meter. A two-inch insulation will cost P30.40 per square meter and will cut out 89% of the loss. A three-inch insulation will cut out 92% of the loss and will cost P65.00 per square meter. Using a life 15 years for the insulation with no salvage value and a minimum attractive return of 8%, what thickness of insulation should be used?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

When a refrigerant vaporizes, it takes heat from its surroundings. The latentheat of vaporization is the amount of heat needed for the refrigerant tovaporize. When 38.5 pounds of R-124 vaporize at 5°F, the latent heat ofvaporization is 2,721.95 Btu. What is the latent heat of vaporization for 1 poundof R-124 at 5°F?
Heat Transfer 1. If you have a piece of extruded polystyrene insulation that has an R-value of 5 hr ft?.°F/Btu per inch [or RSI = 0.8805 (m² · K)/W)]. How many inches of extruded polystyrene do you need in your wall if you want it to have an R-value of 20 hr ft2.°F/Btu [or RSI = 3.522 (m² · K)/W)]? L= 4" 2. What is the transfer of vibrational energy due to collisions between neighbouring atoms and molecules in a solid called? a. Conduction b. Convection c. Radiation d. Latent Heat Radiant Energy 3. Absorptance is a measure of the relative amount of radiant energy absorbed by a surface. Does a shiny and smooth polished aluminum surface have a high absorptance (closer to 1), or a low absortptance (closer to 0)? Absorptance is a ratio of the radiation absorbed to the radiation received, and thus is dimensionless. What about reflectance? Are absorptance and reflectance related? 4. Emissivity is a measure of the relative amount of radiant energy emitted by a surface. Does a shiny and smooth…
calculate the bottom pressure of a sewage tank in which the depth is 20 meters.
A wall of a house, shown in the figure, consists of the items in the accompanying table. If the inside and outside room temperature are 35°C and 15°C, with an exposed area of 150 m2. The total R-factor, Heat transfer through the wall and total thermal resistance in the sequence is given by option No Items Thermal resistance (R') (°C/W) 1 Outside film resistance 0.5 Face brick 1.8 Cement mortar 2.7 Cinder block 2.5 Air space 1.5 6. Gypsum board 0.9 7. Inside film resistance 0.7 234 5
In the graph below, each unit on the horizontal axis is 1.90 103 m³ and each unit on the vertical axis is 0.200 atm. (a) Determine the change in internal energy of the gas if 2042 J of heat is added as it expands in volume along the direct path CA. 1306 J (b) To get the same change in internal energy, how much heat must be added to the gas as it goes along the path CBA? J just need help for part b B A
A BUS IS HAVING A SPEED OF 140 km/hr, IN A PERIOD OF 6 SECONDS, THE BUS DECREASED ITS SPEED TO 100 km/hr. CALCULATE THE RATE OF DECELLERATION.
(a) A well-insulated electric water heater warms 113 kg of water from 20.0°C to 41.0°C in 29.0 min. Find the resistance (in Q2) of its heating element, which is connected across a 240 V potential difference. |ი (b) What If? How much additional time (in min) would it take the heater to raise the temperature of the water from 41.0°C to 100°C? min (c) What would be the total amount of time (in min) required to evaporate all of the water in the heater starting from 20.0°C? min
For a building located in Madrid, Spain with annual heating degree-days (dd) of 4654, a heating load (heat loss) of 30,000 kj/h, and a design temperature difference of 30° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 92%, how muchgas is burned to keep the home at 20° C? State your assumptions.
Hello, I need some help with this question 1 gallon of oil = 4.1 therm and 1 therm costs $1.40 You realized you had 3,600,000 BTU heat loss over a winter month. (1 therm = 100,000 BTU) How much money has been wasted in heat loss?
Thermal comfort in buildings is quantified in terms of a Predicted MeanVote (PMV). Describe in detail the heat and moisture transfermechanisms (e.g. conduction, convection, radiation and evaporation)performed by the human body’s thermoregulatory system needed tomaintain an environmental PMV value of ±0.5.
None