(a) A well-insulated electric water heater warms 113 kg of water from 20.0°C to 41.0°C in 29.0 min. Find the resistance (in Q2) of its heating element, which is connected across a 240 Vpotential difference.|ი(b) What If? How much additional time (in min) would it take the heater to raise the temperature of the water from 41.0°C to 100°C?min(c) What would be the total amount of time (in min) required to evaporate all of the water in the heater starting from 20.0°C?min

Step 1: a. Step 2: b. Step 3:c. Step 4:

Answered: (a) A well-insulated electric water…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
Heat Transfer 1. If you have a piece of extruded polystyrene insulation that has an R-value of 5 hr ft?.°F/Btu per inch [or RSI = 0.8805 (m² · K)/W)]. How many inches of extruded polystyrene do you need in your wall if you want it to have an R-value of 20 hr ft2.°F/Btu [or RSI = 3.522 (m² · K)/W)]? L= 4" 2. What is the transfer of vibrational energy due to collisions between neighbouring atoms and molecules in a solid called? a. Conduction b. Convection c. Radiation d. Latent Heat Radiant Energy 3. Absorptance is a measure of the relative amount of radiant energy absorbed by a surface. Does a shiny and smooth polished aluminum surface have a high absorptance (closer to 1), or a low absortptance (closer to 0)? Absorptance is a ratio of the radiation absorbed to the radiation received, and thus is dimensionless. What about reflectance? Are absorptance and reflectance related? 4. Emissivity is a measure of the relative amount of radiant energy emitted by a surface. Does a shiny and smooth…
Question 2 b) Water flows from a large reservoir through a pipe system which consists of 200 mm diameter of pipe and 50 mm diameter of nozzle as shown in Figure 3. By neglecting all energy losses, calculate; (ii) Velocity and pressure at A Note: Nozzle is exposed to the atmosphere 4 m 2 m Nozzle Figure 3
I need the answer as soon as possible
As shown in the figure, a 300-ft³ tank contains 25 lb of H₂O initially at 30 lbf/in². The tank is connected to a large steam line carrying steam at 200 lbf/in2, 450°F. Steam flows into the tank through a valve until the tank pressure reaches p2 = 140 lbf/in² and the temperature is 400°F, at which time the valve is closed. Steam at 200 lbf/in.2, 450°F Valve (1) Tank Initially: 30 lbfin.², m₁ = 25 lb (2) Finally: P₂ lbfin.², 400°F. Determine the amount of mass that enters the tank, in lb, and the heat transfer to the tank from its surroundings, in Btu.
2. A 100 ft. long structural steel beam is used in the construction of a bridge in an area where the temperature may fluctuate 110 ° F. What would be the expected change in length of the beam? (Give your answer in inches)
I need the answer as soon as possible
3) A body at an unknown temperature is placed in a room with constant temperature of 30 °F. If after 10 minutes the temperature of the body is 0 °F, and after 20 minutes the temperature of the body is 15 °F, find the unknown initial temperature.
2- The density of a liquid is to be determined by an old 1-cm-diameter cylindrical hydrometer whose division marks are completely wiped out. The hydrometer is first dropped in water, and the water level is marked. The hydrometer is then dropped into the other liquid, and it is observed that the mark for water has risen S cm above the liquid-air interface. If the height of the original water mark is 12.7 cm, determine the density of the liquid S (cm) Last names starting 0.95 with A to L Unknown liquid Mark for water S cm
Two thermometer. one reading and the other are both immersed in a fluid. If the farenheit reading is half of the celcius reading, a.) What is the farenheit reading? b.)what is the equivalent temperature of the fluid in degrees rankine?
i need the answer
Water is flowing in a fire hose with a velocity of 1.0 m/s and a pressure of 200000 Pa. At the nozzle the pressure decreases to atmospheric pressure (101300 Pa), there is no change in height. Use the Bernoulli equation to calculate the velocity of the water exiting the nozzle.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS