Im is A motor with rotor inertia of 0.03 kgm and maximum torque of connected to a uniformly distributed arm with a concentrated mass at its end, as shown in Figure. Assume that the two gears have 0.002 kgm² and 0.005 kgm² inertias respectively. Ignoring the viscous friction in the system. If the gear ratio is 5, the maximum angular acceleration it can develop is: (Show your work) 399 rad/s² 166 rad/s² 270 rad/s² 370 rad/s² 0.5 m m=3Kg m=3Kg

Im is A motor with rotor inertia of 0.03 kgm and maximum torque of connected to a uniformly distributed arm with a concentrated mass at its end, as shown in Figure. Assume that the two gears have 0.002 kgm² and 0.005 kgm² inertias respectively. Ignoring the viscous friction in the system. If the gear ratio is 5, the maximum angular acceleration it can develop is: (Show your work) 399 rad/s² 166 rad/s² 270 rad/s² 370 rad/s² 0.5 m m=3Kg m=3Kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q4 shows a Mach trim system from a 737-800. It consists of a hydraulic motor driving gear A which drives gear B. Gear B is directly connected to the horizontal stabiliser via rack and pinion as depicted below. Gear A has a mass of 6kg, a radius of gyration of KGA = 0.1235m and an angular acceleration of 20kg, and a radius of gyration of Ö = 0.2t rad/s². Gear B has a mass of m = m = = 0.5341m. If the system starts from rest, determine the following when t = 3s: KGb a) The velocity of the gear rack. b) The distance the rack has travelled. c) If there is a contact force between the rack and gear B of 50N, determine the contact force between Gear A and B. d) The applied torque from the hydraulic motor. 100mm 500mm B 200mm Figure Q4-Mach Trim System tastes ins
Please answer correctly. Show all the steps
Solve correctly
Theory of Machines -Thired Stage. a/ A pinion having 20 in volute teeth of module pitch 6mm ayear wheel rotutes at 2o r.p.m. and traurmits /.5kw to l having 5o teeth The adden dum on both the wheels is Vy of the circular pitch -The angle of obliquity is 20' Find ca) the bength of the path of appsoach (b) the length of the arc of approach,(c) the normal force betmen the teeth atn Instant where thare is only pairof tath in Con tact. [Ans. 13.2Fmm, 14.02 mm. il 93NJ
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a power of 28 hp. Gears 4, 5, and 6 have 24, 36, and 144 teeth, respectively. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Fixed What torque can arm 3 deliver to its output shaft? The torque that arm 3 delivers to its output shaft is lbf-in.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
I need answer please
As shown in the figure, 2 lumped masses that are not in the same plane are connected to a shaft between the bearings at A and B. The spindle is rotated counterclockwise with a constant speed of 1450 rpm. Perform the dynamic balancing of this prototype rotor system. -Required corrective masses in the L and R planes from the C axis of rotationIt will be placed at a distance of 50 mm. -The values of the required corrective masses will be found in grams. -The angle positions of the necessary corrective blocks will be written in polar style at the last stage. -For the solution, the "Algebraic Solution" method based on Cartesian components will be used.
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
solve, show all steps for given solution.
A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kW to a gear wheel. The pressure angle is 20° and module is 20mm. The reaction exerted by the pinion at the centre of thc shaft is