Answered: Im 2.4m 0.5 m H 1.5 m 1 m Sell B 2.2 m…

Engineering

Civil Engineering

Im 2.4m 0.5 m H 1.5 m 1 m Sell B 2.2 m 1.5 m 1.7 m Datum 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Exercise 1 A soil profile is shown in Figure Calculate the values of o, u, and o' at points A, B, C, and D. Plot the variation of o, u, and o' with depth. Dry sand roundwater table Thickness (ft) Unit weight (Ib/ft) Layer no. Laver IE H = 5 H2 = 6 H3 = 8 Ya = 112 Ysat = 120 Ysat = 125 Sand I II III TTE Figure 1
The maximum and minimum void ratios for sand are 0.805 and 0.501 respectively. The field density test performed on the same soil has given the following results:ρ = 1.81 g/cm3, w= 12.7 %. Assume G= 2.67. Compute the dry density in Mg/m3. a.1.606 b.1.85 c.1.512 d.1.65
a. Plot P0 and P1 readings with depth in one plot and show the groundwater table.b. Calculate the hydrostatic porewater pressure with depths.c. Evaluate the profile of material index, ID, and dilatometer modulus, ED with depths.d. Determine the soil type from material index. What types of soil are encountered at this site?e. Use the material index, ID, and dilatometer modulus, ED, to determine the profile of soil unit weight withdepths.f. Show three side-by-side plots for (1) material index, ID, (2) dilatometer modulus, ED, and (3) soil unitweight with depths. Make sure to match the ground surface elevation and bottom for all three graphs.g. Calculate the total and effective overburden stresses, and plot the profiles of total and effective overburdenstresses and hydrostatic porewater pressure with depths in one plot
22. A sample of moist soil has a water content of 26%, a void ratio of 1.1, and a Gs of 2.7 a. Draw the phase diagram and fill it in with numerical values b. Determine S, n, yd, Ysat, Ysub
Water table is at at depth of 10m in a silty soil mass. The sieve analysis indicate the effective diameter D10 of the soil mass is 0.05 mm. Determine the capillary pressure. Assume void ratio, e=0.51, C=0.5
Consider two horizonal soil layers, each is isotropic, the upper layer 1 is sitting directly on the top of bottom layer 2. Layer 1 has a thickness of 2 m and a hydraulic conductivity of 0.26 m/day and layer 2 has a thickness of 4 m and a hydraulic conductivity of 0.95 m/day. In this case, calculate the equivalent horizontal hydraulic conductivity in m/day.
A soil with a volume of 0.0283 m3 has a specific gravity of 2.7, a dry weight of 0.376 kN, and a wet weight of 0.459 kN. 1) Determine the volume of voids (Ans. 0.0149 m3) 2) Determine the void ratio (Ans. 1) 3) If the soil was submerged, determine the effective unit weight (Ans. 8.34 kN/m3)
1. A soil deposit consists of three horizontal layers of soil: an upper stratum A (1m thick), a middle stratum B (2m thick) and a lower stratum C (3 m thick). Permeability tests gave the following values: Soil A, k = 0.3 mm/sec; Soil B, k = 0.2 mm/sec; Soil C: k =0.1 mm/sec. a) Determine the ratio of the average coefficients of permeability of the soil deposit (all three layers) in the horizontal and vertical direction. b) Beneath the deposit there is a gravel layer subjected to artesian pressure, the surface of the deposit coinciding with the ground water level. Standpipes show that the fall in head across soil A is 150 mm. Determine the value of the water pressure at the top of the gravel. 150 mm Soil A, Im Soil B, 2m Soil C, 3m Gravel Figure 1
A sample of dry sand having a unit weight of 16.50 kN/m and a specific gravity of 2.7 is placed in the rain. During the rain, the volume of the sample remains constant, but the degree of saturation increases to 40%. Determine the unit weight of the sample after being in the rain. Select one: O a. 15.02 b. 17.98 C. 20.53 d. 24.18
The hgure shows a granular soil in a tank having a downward seepage. The water level in the tank is held constant by adjusting the supply from the top and the outflow at the bottom. The void ratio of the soil is 0.50 and the specific gravity is 2.7. H,0 0.8 m 1.1 m A 3.6 m 5.4 m B C If a plczometer is placed at point B, to what height the water will rise above this point?
2. The field unit weight of the soil sample 1s 1960 kg/m3 and the unit weight of the soil particle is 2700 kg/ m. If the emax = 0.69 and emin = 0.44, determine the following: a) Specific gravity b) Dry unit weight if water content is 15% c) Porosity d) Relative density e) Saturated unit weight f) Effective unit weight g) Weight of water in KN that must be added per m3 for a 90%-degree saturation h) Mass of water in kg to be added per 2.5m3 to reach full saturation i) If max dry unit weight is 18KN/m³, what is the percentage compaction? j) Is it within the allowable compaction range of 95 of relative +0.2?
Sand cone equipment is used to perform a field density on compacted earth fill. Sand is used in the cone and is known to have a bulk density of 15 kN/m3. The wet weight of soil sample from the test hole is 20.601 N. The dry weight of soil sample is 17.926 N. The weight of the sand in the sand cone to fill the test hole is 16.053 N. Determine the in-place dry density in kN/m3 of the tested soil.