HW3: Time Response(1) For the shown block diagram, determine(i) The closed loop transfer functions,Els)C(9)/R(s) = .(ii) The system type r(iii) The de gain =(iv) The steady state error for step input.. .and ramp input=...............

Answered: Image /qna-images/answer/6c81f3d3-671d-4f89-97de-4036bad00874.jpg

Answered: (ii) The system type ........ ......*..…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(H4-03) Fixed-Bias And Emitter-Bias Configuration. (BJT Configurations, BJT DC Biasing). (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
what you use everyday that would require the use of an amplifier circuit. Take into consider the Class of amplifier the device is using and the fidelity of the signal it produces.
Hand Calculation: Since you now have the values of R1 and R2 resistors, obtain numeric value of voltage gain Av=Vo/Vi, and numerical values of input and output resistances Ri and Ro. Note that you need to DC analysis first. Do a hand calculation and calculate the DC collector current or IC. This is needed in order to calculate the small signal parameters gm and rπ and in turn to obtain the Av , Ri and Ro Hence, first perform a DC analysis (use the circuit in Figure 1 and take all capacitors open) and assume your transistor has a β=140.
Subject: Analogy Electronic and Circuit Derive Output Impedance & Voltage Gain for self bias un-bypass circuit using hybrid model
1. Discuss the difference between Passive and Active Components? Give examples
4) Below is the small signal model of a multistage amplifier. Using this model, write the equationsthat you would need to determine the voltagegain. IMPORTANT: You only need to providethe equations that you would need to determinethe voltage gain. You DO NOT need to combine and simplify the equationsto determine a final expression for the voltagegain. Vin Vo Vb vo1 Rb R13 Vbe1 Vbe2 'e gm 1 Vbe1 gm 2 Vbe2 Rc2 Rc1 Re
Increasing the proportional gain Kp wll ...the system tendency also ... .. toward instability decrease fixed increase None

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

(ii) The system type ........ ......*.. (iii) The de gain- ....... ..... ....