(II) A hydraulic press for compacting powdered sampleshas a large cylinder which is 10.0 cm in diameter, and asmall cylinder with a diameter of 2.0 cm (Fig. 10–51).A lever is attached to the small cylinder as shown. Thesample, which is placed on the large cylinder, has an areaof 4.0 cm?. What is the pressure on the sample if 320 N isapplied to the lever?320 NSample10.0 cmydraulicuid-Small cylinder-2.0 cmFIGURE 10-51 Problem 21.

Given: The force applied to the lever is F=320 N. The diameter of the large cylinder is D=10 cm. The…

Answered: (II) A hydraulic press for compacting…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given the following values, calculate their relative compactness ydmax=2,250 Kg/cm?, ydmin=1,120 Kg/cm?, ydnat=1,635 Kg/cm?,
Q1
In powder processing, a cylinder with a diameter of 2 inches and a height of 10 inches is to be made from fine copper powders. A single-action press is used for compaction. If the average density of the green product is 7 g/cm3 at the bottom half of the cylinder, estimate the compaction pressure at the punch surface. Assume no friction between the powders. The coefficient of friction between particles and containers is 0.2.
Granule strength is very important in pressing powders. The force applied to a granule with a radius of 1 mm is 0.5 Newton. Calculate the breaking strength of the granule. b) It is observed that the pressed granules break easily during pressing. Write down the reasons of this situation and what would you take precations to solve this problem? Why? (please write down 3 precautions with reasons). odluck
Your die setter brings you a print of a cylinder with a 2 inch outside diameter and a 1.75 inch inside diameter. The cylinder is to be molded of iron powder with a green density of 6.8 g/cc. The apparent density of the powder is 2.9 g/cc. What is the die fill if the green part is to have a height of 2.5 inches? (show your work)
1. How did the consistency of the jelly change when you changed the ratio of sugar to pectin? 2. Why did the consistency change when you changed the ratio of sugar to pectin?
GKN Sinter Metals Company pressed iron powders using a compaction pressure of 600 MPa to produced a cylindrical bearing which is 70 cm long and has internal and external diameters of 8 cm and 16 cm, respectively. Determine (a) the most appropriate pressing direction, (b) the required press tonnage to perform this operation, and (c) the final weight of the part if the porosity is 12%, given that the density of iron, ρ = 7.87 g/cm3. Assume shrinkage during sintering can be neglected
I1
As the lead engineer for a LPG storage project, you are overseeing the design of pressure vesselssuch as those shown below. Identify which test (or tests) is mostsuitable to pick a material and thickness for the spherical shell of the pressure vessel. Why these are the relevant tests. Explain what information these tests provide and why it is important to determining material and thickness.
Choose the best
Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s') Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175
For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene powder with a density of 0.900 g/cm³ and crystalline polyethylene powder, what is the percent crystallinity of the manufactured parts? (The density of polyethylene in its amorphous and crystalline states is 0.870 g/cm³ and 0.998 g/cm³ respectively) O a. % Crystallinity = 45.96% O b. % Crystallinity=55.25% O c. % Crystallinity = 53.35% O d. % Crystallinity = 61.20% Oe. % Crystallinity = 35.50%

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS