For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene powder with a density of 0.900 g/cm³ and crystalline polyethylene powder, what is the percent crystallinity of the manufactured parts? (The density of polyethylene in its amorphous and crystalline states is 0.870 g/cm³ and 0.998 g/cm³ respectively) O a. % Crystallinity = 45.96% O b. % Crystallinity = 35.50% c. % Crystallinity = 61.20% O d. e. % Crystallinity = 55.25% % Crystallinity = 53.35%

For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene powder with a density of 0.900 g/cm³ and crystalline polyethylene powder, what is the percent crystallinity of the manufactured parts? (The density of polyethylene in its amorphous and crystalline states is 0.870 g/cm³ and 0.998 g/cm³ respectively) O a. % Crystallinity = 45.96% O b. % Crystallinity = 35.50% c. % Crystallinity = 61.20% O d. e. % Crystallinity = 55.25% % Crystallinity = 53.35%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

powdered metal question
For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene powder with a density of 0.900 g/cm3 and crystalline polyethylene powder, what is the percent crystallinity of the manufactured parts? (The density of polyethylene in its amorphous and crystalline states is 0.870 g/cm3 and 0.998 g/cm3 respectively) a. % Crystallinity = 35.50% b. % Crystallinity = 55.25% c. % Crystallinity = 53.35% d. % Crystallinity = 61.20% e. % Crystallinity = 45.96%
The part shown in Figure is to be pressed from fine copper powders using a compaction pressure of 1000 MPa. Dimensions are milimetres. Determine a) the required press tonnage to perform this operation b) the final weight of the part if the porosity is 15%. Assume shrinkage during sintering can be neglected. (the desity of copper =8,97g/cm³ ) 65 30 25 12 20
Given the following values, calculate their relative compactness ydmax=2,250 Kg/cm?, ydmin=1,120 Kg/cm?, ydnat=1,635 Kg/cm?,
3
In powder processing, a cylinder with a diameter of 2 inches and a height of 10 inches is to be made from fine copper powders. A single-action press is used for compaction. If the average density of the green product is 7 g/cm3 at the bottom half of the cylinder, estimate the compaction pressure at the punch surface. Assume no friction between the powders. The coefficient of friction between particles and containers is 0.2.
Q2 (a) How are glass products formed or shaped ? (b) What are some major limitations to the extensive use of composite materials in engineering applications ?
Question Seven (a) For refractory ceramic materials, cite two characteristics that improve with and two characteristics that are adversely affected by increasing porosity. (b) Show that the minimum cation-to-anion radius ratio for a coordination number of 4 is 0.225. (Hint: Use the AX crystal structure, assuming the anion spheres touch in plane). (c) The unit cell for Al>Os has hexagonal symmetry with lattice parameters a = 0.4759 nm and c 1.2 nm. If the density of this material is equal to 3.99 g/cm' and is calculated according to the formula n'(E Ac+ EAA) V.NA Calculate the atomic packing factor for Al>O, given that the ionic radius for AI is 0.053 nm and i 0' is 0.140 nm. Take N, = 6.023 x 1023 atoms/mole. (d) Mention any three industrial ceramics and indicate their applications.
Granule strength is very important in pressing powders. The force applied to a granule with a radius of 1 mm is 0.5 Newton. Calculate the breaking strength of the granule. b) It is observed that the pressed granules break easily during pressing. Write down the reasons of this situation and what would you take precations to solve this problem? Why? (please write down 3 precautions with reasons). odluck
(a) Following is the Super Asia plastic body washing machine. You are asked to write itsmanufacturing process for the highlighted zone. Draw and label the complete diagram forthat process. Write your reason why you have adopted particularly that manufacturingprocess (b) If the portion of washing machine on the above said picture is metallic then how will yourmanufacturing process change. Draw and label the new manufacturing method.
A Silicon Carbide powder has an internal energy of 3 X 108 J/m³, a surface tension of 1.2 J/m², and a total energy of 2.6 X 10-¹5 J. What is the smallest diameter that this powder may be ground without agglomerating? (show your work)
Your die setter brings you a print of a cylinder with a 2 inch outside diameter and a 1.75 inch inside diameter. The cylinder is to be molded of iron powder with a green density of 6.8 g/cc. The apparent density of the powder is 2.9 g/cc. What is the die fill if the green part is to have a height of 2.5 inches? (show your work)