If V esa = 7 V, C, = 86 nF and C2 = 126 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: r will be taken into account in the calculations. +20 V 10 k2 C: 22 Ma VesT-35 V k-0.3 x 10 R-30 uS O a. 164,26 Hz O b. 131,41 Hz O 114,98 Hz O d. 82,13 Hz e. 98,55 Hz O f. 32,85 Hz O g. 49,28 Hz O h. 16,43 Hz

If V esa = 7 V, C, = 86 nF and C2 = 126 nF in the circuit in the figure, what is the low cut-off frequency of the system? NOTE: r will be taken into account in the calculations. +20 V 10 k2 C: 22 Ma VesT-35 V k-0.3 x 10 R-30 uS O a. 164,26 Hz O b. 131,41 Hz O 114,98 Hz O d. 82,13 Hz e. 98,55 Hz O f. 32,85 Hz O g. 49,28 Hz O h. 16,43 Hz

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ELECTRONICS LAB
Problem 4 The following practical differentiator has V = 80 sin(wt), R₁ = 10 KM, R₂ = 500 KG and C= 150 µF. Find: A- The breaking frequency F B. The output voltage at 1000 F C The output voltage at f= 50 Hz. Vin RI HH R2 www Vout
how the bleeding resistor and zener diode regulate the DC voltage across the filter capacitor of the power supply circuit.
Calculate the cutoff frequency of the circuit. R₁ = 2.02 KQ, R2 = 2.02 kQ, C₁ = 0.05 uF, C₂ = 0.05 uF RG = = 15 ΚΩ, RF = 40 ΚΩ Note: Express your answer in Hz and in 2 decimal places. No need to write the unit. V₁ C₁ HA R₁ RG C₂ R₂ RF Op-amp V₂
Calculate current gain, input and output impedance, and linearity. Beta = 90 IS = 2E-15
Q6// Determine Ve, VB, VE, Ic, Ig and Ig for the circuit shown in figure below (B=100 & a= 0.9) Vcc = +22 V Rc 10 Kohm 39 Kohm RB C2 • Vo C1 1µF Vin • Q1 1µF
18 ut of estion 9 In Designing a lag compensator for the shown system, the only thing left is to determine the gain K. Take the closed loop poles ass-0.2 0.9. Determine Ke. R(s) Select one: O a. -7 O b. 1.06 O c. 2.50 O d. 1.94 Oe. 0.88 Ke $+0.5 $+0.05 lag compensator Consider the followin s(s+1) plant C()
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo
SIGNAL Mention the function or work of each component in the circuit? + Vcc Rc Rc Cc HH www R₁ Cin HH R₂ www. RE Cc HH CE www R₁ 30 www wwww RE CE OUTPUT
Determine the DC bias values using DC equivalent circuits (in order of VE, VB, VC)
(c) A 2400 V, 1000 KVA, 0.85 power factor (PF) lagging, 50 Hz six-poles, Y-connected synchronous generator has a synchronous reactance of 1.4 2 and an armature resistance of 0.15 2. At 50 Hz, its friction and windage losses are 25 kW, and its core losses are 15 kW. The field circuit has a DC voltage of 230 V, and the maximum IF is 10 A. The resistance of the field circuit is adjustable over the range from 20 to 200 £2. The Open Circuit Characteristic (OCC) of this generator is shown in Figure Q1(c). Calculate the internal generated voltage, EA of this machine at rated conditions. (i) (ii) (iii) Determine the required field current to make Vr equal to 2400 V when the generator is running at rated conditions. If this machine is operating at rated conditions, determine the input torque, TAPP that must be applied to the shaft of this generator.
92 ۱ ۹:۱ ص Qs= 1107 and Qp= 1041 Qs= 1207 and Qp= 1241 Qs= 1007 and Qp= 1041 Qs= 1107 and Qp= 1141 In the figure shown below we can find output current is equal to.. . if the input voltage is equal to 12 mv 12 kO 12 ka 6 ka No option is correct 10 = 32 uA 10 = 34 uA 10 = 38 uA 10 = 36 uA In the fig. shown below we can find the higher critical frequency due to the input