If the weight of sample of sand in sieve analysis test was 420 gm and the weight retained on sieve are shown in table below. Is the sand satisfying the specification? Calculate the fineness modulus of sand and what is the average size ? Sieve size 10 5 2.36 1.18 0.6 0.3 0.15 < 0.15 (mm) Weight 8.4 63 96.6 143 59 34 16 retained (gm)

If the weight of sample of sand in sieve analysis test was 420 gm and the weight retained on sieve are shown in table below. Is the sand satisfying the specification? Calculate the fineness modulus of sand and what is the average size ? Sieve size 10 5 2.36 1.18 0.6 0.3 0.15 < 0.15 (mm) Weight 8.4 63 96.6 143 59 34 16 retained (gm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the Fineness modulus of sand for the results of sieve analysis
1. The following are the results of a sieve analysis U.S. Sieve No. 4 10 20 40 60 100 200 Pan Mass of Soil retained (g) 0 18.5 53.2 90.5 81.8 92.2 58.5 26.5 a) Determine the percent finer than each sieve and plot a grain-size distribution curve. b) Determine D10, D30, and Doo. c) Calculate the uniformity coefficient Cu d) Calculate the coefficient of gradation Ce
Determine the uniformity coefficient and coefficient of gradation from the following data:
The results of the sieve analysis done on a soil are shown below. Sieve No. Diameter Soil A 4 4.760 96 6 2.380 91 10 2.000 89 20 0.840 85 40 0.420 81 60 0.250 78 100 0.149 67 200 0.074 64 LL 40 PL 30 Determine its classification using USCS. ML MH None of the above CL CH
Situation 3. Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4 6 10 20 40 60 100 200 Pan Diameter (mm) 4.760 2.380 2.000 0.840 0.420 0.250 0.149 0.074 Soil Sample Mass Retained (g) 100 180 86 160 105 134 110 65 45
Make comments about the general properties of the soil by classifying the floors given in the figures in the laboratory test results according to AASHTO and UCSC.
Someone can help me with this one. Please
Standard Test Method For Penetration of Bituminous test 1. Importance of penetration test.2. Effect of temperature, load and time on penetration values. State otherconditions.3. The use of different grade in different climates.4. What is the meaning of “consistency of bituminous materials”?5. Which value of penetration can be used in construction of roads in Iraq?
the results of the sieve analysis done on a soil are shown below. Determine its classification using USCS. a. None of the above b. ML c. MH d. CL e. CH
Q.2) Answer the following question. 1- The sieve analysis below was done for which type Weight of sample = 2000gm Sieve size in. (mm) 3/8" 9.5 mm No.4 4.75 mm No.8 2.36 mm No.16 1.18 mm No.30 0.6 mm No.50 0.3 mm No.100 0.15 mm Pan Percent Weight retained (g) retained 0 2000*100 94 →0 Klcc→ -2000 4032000X100 358-2009 08 72 2212000x100 Percent cumulative @ 4.7 20 i 75 982 57 360 72000 Alco isies 39 492-20000 24.614 · 100 > 95 3 of aggregate. Percent passing 0 5 25 уз 61 86 97 317 ASTM Limit 100 95_100 80_100 40 85 25_60 10_30 2_10
Given below is the result of a sieve analysis done on a soil sample.Sieve No. Diameter Percent Passing %4 4.750 9510 2.000 8220 0.850 7340 0.425 5360 0.250 23100 0.150 14200 0.075 7Pan --- 0Determine the value of the coefficient of uniformity
a. determine the effective size diameter d. determine the coefficient of uniformity c. determing the coefficient curvature The results of sieve analysis are shown below. Sieve No. Opening Size (mm) Mass Retained (g) 4 4.750 10 2.000 18.5 20 0.850 53.2 40 0.425 90.5 60 0.250 81.8 100 0.150 92.2 200 0.075 58.5 Pan 26.5