If the V is incident on a control surface with a cross-sectional area corresponding to a circle of radius, R, what is the volumetric flow rate? Assume în is in the direction of the x- axis (i.e. unit normal is (1,0,0)). V = (1.5, 6, 6) m/s and R = 1 cm

If the V is incident on a control surface with a cross-sectional area corresponding to a circle of radius, R, what is the volumetric flow rate? Assume în is in the direction of the x- axis (i.e. unit normal is (1,0,0)). V = (1.5, 6, 6) m/s and R = 1 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If pipe 1 diameter = 55 mm, mean velocity 2 m/s, pipe 2 diameter = 40 mm, mean velocity 3.5 m/s, and pipe 3 diameter 90 mm. 3 then the discharge value Q1 is L/S 2
The pressure loss p in a pipe is related to the flow rate Q by the equation P = KQ^n, where K and n are constants. If K = 190 x 10³determine the value for n when a flow rate of Q = 0.04 m³/s causes a pressure loss of 180 Pascals.
Steady, incompressible and inviscid water flows inside the given system, if the force F is needed to hold the system stationary, what is the work W (W=F x L) joule is needed to move the systema distance L=6.3 m. V1=3 m/s A1=0.1 m p1=200 kpa 2 m A2=0.2 m ENG 10:06 US 07/05/2 DELL FZ F8 F9 F10 F11 F12 PrtScr Insert Delete PgUp PgDn
None
1.) A process fluid (μ = 3 cP, p = 1210 kg/m³) is flowing through a 5.8-cm ID pipe with an average velocity (Uavg) of 2.5 m/sec. Calculate/estimate the following: a) What is the velocity profile from the center of the pipe (r=0 cm) to the pipe wall (r; = 2.9 cm)? b) The length of the pipe (4) is 10 feet. Calculate the pressure drop through the pipe using the Hagen-Poiseuille law. c) Calculate the Reynolds number for this system. d) Is the flow in the pipe laminar or turbulent? e) Estimate the Fanning friction factor (f) in this system. f) What is the pressure drop (AP) in the system if friction is considered?
In mechanical fluid
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (3) Calculate the drag force FD_________N (2 decimal places)
Q5
Correct answer only
7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched element and through a force balance, show that the velocity distribution across the layer is: dx Y sin e (b2 – s2) 2 µ и 3 Free Surface an expression for the at the free b. Derive t dx liquid velocity surface. c. Derive an discharge per unit width. d. Derive Fixed y s dx expression for the Wall b an expression for the shear stress at the fixed wall.
Consider flow of blood in the microvessels of the body, assuming Poiseuille’s law holds and that the viscosity of the blood is constant. Consider a parent vessel that bifurcates into two daughter segments, all within the microcirculation and with blood flow described using Poiseuille’s law (assume that each segment has a different diameter and length).Denoting the pressure at node i by pi (i=1,2,3,4), and the flux in segment j by Qj (j=1,2,3), write down expressions for the segment fluxes in the network, in terms of the nodal pressures. How are the three volume fluxes related, and why? Assuming that the pressures at nodes 1, 3, 4 (the boundary nodes) are known, write down an expression for the pressure at the interior node, p2.