If the T-beam is subjected to a vertical shear V = 14 kips, determine the maximum shear stress (ksi) in the beamWhere: tf = 2.4 in and d = 7 in If the T-beam is subjected to a vertical shear V = 14 kips, determine themaximum shear stress (ksi) in the beamWhere: tf = 2.4 in and d = 7 in4 in.4 in.tf4 in.dA

Answered: Image /qna-images/answer/d6d952ae-107d-41ff-8612-73b4af8f461d.jpg

Answered: If the T-beam is subjected to a…

If the T-beam is subjected to a vertical shear V = 14 kips, determine the maximum shear stress (ksi) in the beam Where: tf = 2.4 in and d = 7 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If Øxx = 110 MPa, Oyy = - 86 MPa, ozz = 55 MPa. Txy = 60 MPa, and allþther components are zero. Determine the principal stresses and the direction cosines of the principal axis. Also find the octahedral normal and shear stress components. Q.4:
Asap
3
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 24 ksi, and Sxy= 16 ksi. (a) Determine the principal stresses (1 > 2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: Opl = Op2 = Tmax = Sxy 0 ksi. ksi. ksi.
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy-17 MPa, S, - 60 MPa, and Swy- 29 MPa. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses (ơp > op2) and the maximum in-plane shear stress Tmax acting at the point. (c) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g, see Figure 12.15 or Figure 12.16) Say Answers: MPa. Opl = MPa. MPa. Tmax = 0, =
Consider a point in a structural member that is subjected to plane strèss. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S= 24 MPa, Sy= 34 MPa, and Sy= 31 MPa. (a) Determine the principal stresses (o,1 > O2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, cločkwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: MPа. MPa. Op2 = MPa. Imax =
Problem 5: The stresses on the x-y-axes are o, = 8 ksi, o, = 12 ksi, and Ty = -5 ksi. Draw the Mohr's circle for this stress state. Identify the maximum shear stress from the Mohr's circle, and draw the maximum shear stress element, specifying its orientation.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 37 MPa, Sy = 10 MPa, and Sxy = 41 MPa. (a) Determine the principal stresses (6,] > 6,2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: MPa. Opl = MPa. Op2 = Tmax = MPa.
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry
1.1