27.If the system shown below is used to run a refrigerator, which ofthe following is true for the x to z step?pressurevolumeyZA. The work is negative and heat is added to the systemB. The work is positive and heat is added to the systemC. The work is negative and heat is removed from the systemD. The work is positive and heat is removed from the system28.Refer to the y to z step in the PV diagram of the previous question.If heat was added to the system, which of the following must alsobe true?A. W < 0, and AU = 0B. W = 0, and AU > 0C. W = 0, and AU = 0D. W = 0, and AU <0E. W > 0, and AU = 0

Here a diagram is given which representing refrigeration cycle. The direction of cycle is x to z. We…

Answered: If the system shown below is used to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

** I mainly just need help with process 4-1. I do not remember PV constants well.
During a warm summer night, the air inside a house is maintained at a fixed temperaturevia an air conditioning system. Separating the inside air from the outside air is a plane wall.The inner surface of the wall exchanges energy with the air inside the house via convection;the outer surface of the wall exchanges energy with the surrounding air via convection andthe night sky via radiation. Known system parameters are listed below.Inner air temperature ?? = 26°CSurrounding air temperature ?∞ = 33°CNight sky temperature ?? = 4°CWall thermal conductivity ?Wall-air convection coefficient ℎ = 30 W/m2-KWall emissivity ? = 0.85Wall thickness ?a) Set up the equations that you allow you to calculate the heat flux through the wall.Keep everything symbolic and be careful with your heat transfer directions.Hint: If the AC is on, what does that tell you about the net direction of heat transfer?b) Write a computer script that calculates the heat flux through the wall for 20 values ofthe ratio of the…
This is one whole question can you please help me
The van der Waals (vdW) equation is a cubic equation of state (CEOS) which may be used to calculate the volume or pressure conditions for a real gas: P= a = RT a v-b v² Here, v represents the molar volume of the gas, and P, R, and T' are the absolute pressure, ideal gas constant, and absolute temperature of the gas, respectively. The values a and b are component dependent an may be calculated using: 27 R²T² 64 P C and b= 1 RT 8 Pc So, when both the critical pressure (Pc) and critical temperature (Tc) are known, one can apply the vdW CEOS to give a more accurate calculate more accurate properties than the ideal gas law. One must be careful to use absolute values for the pressure & temperature (e.g., unit of K not °C) and a value for the gas constant that is consistent with the unit desired (such as R = 0.0083144598 L·bar/K·mol) Do the following: a) Calculate the molar volume (L/mol) of nitrogen gas (Pc = 33.96 bar, Tc = 126.19 K) at 5 bar and 30°C using both the ideal gas law & using…
Please solve it fast in handwritten format
Please help and show work.
Your house has an electric water heater. Several friends are visiting you over the weekend and they are taking consecutive showers. Assume that at the maximum heating level, the heater uses 50 kW of electricity. The water use rate is a continuous 4 gallons per minute with the new water saving showerhead you recently installed. Your very old showerhead had used 7 gallons per minute. You replaced the showerhead because you learned that heating water was the second highest energy use in your home. By slowing the flow of water through the heater, the water temperature should increase to a higher temperature. (a) What is the change in temperature (T) for the old showerhead? (b) What is the change in temperature (T) for the new showerhead? Assume the system is at steady sate, and all of the 50 kW energy used is heating the water.
Please provide solution. Thanks!
Task 1 Write down the energy balance equation from the first law of thermodynamics for a closed system and then put the equation for an open system. Explain the difference between the two equations.
Draw and discuss the FBD for the following system. • Label all forces and directions. How many unknowns are there? (Remember, an unknown does not have to be a force. It can also be a dimension, angle, etc.) • How many equilibrium equations can you create? • Is there enough information to solve for the unknowns? Explain. ● Draw pulley A as your particle. B 20° A 100 N F
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
A hot water leak in one of the faucets of your apartment can be very wasteful. A continuous leak of one quart per hour (a "slow" leak) at 155 degrees°F causes a loss of 1.81 million Btu per year. Suppose your water is heated with electricity. a. How many pounds of coal delivered to your electric utility does this leak equate to if one pound of coal contains 12,000 Btu and the boiler combustion process and water distribution system have an overall efficiency of 28%? b. If a pound of coal produces 1.81 pounds of CO2 during the combustion process, how much extra carbon dioxide does the leaky faucet produce in a year

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS