O d. 7.21 secClear my choiceIf the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-looppoles on the s-plane. Type a, b, c or d.ts =7 sec and wn 1.195 rad/sec.s-planejajo s-planes-planejws-planeX----J2.047X---J1.047X------j0.57X-J0.57- 1.57-0.57-2.047-1.047(a)(b)(d)Answer:In order to change the behavior of a 2nd order underdamped system, we need to move its closed-loop poles on the s-plane as shown. With this move, what happened to the settling time? it .EN9:49 PM4/19/2021

Answered: Image /qna-images/answer/6a04fc57-6cf2-46c4-8787-aee80800ef4e.jpg

If the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-loop poles on the s-plane. Type a, b, c or d. ts=7 sec and wn = 1.195 rad/sec. ja s-plane jo s-plane ja s-plane jw s-plane X.----J2.047 X---j1.047 X------ j0.57 X- J0.57 - 1.57 -0.57 -2.047 -1.047 X (a) (b) (c) (d)

If the settling time (2% criterion) and the peak time of a 2nd order system are given, find the location of the 2 closed-loop poles on the s-plane. Type a, b, c or d. ts=7 sec and wn = 1.195 rad/sec. ja s-plane jo s-plane ja s-plane jw s-plane X.----J2.047 X---j1.047 X------ j0.57 X- J0.57 - 1.57 -0.57 -2.047 -1.047 X (a) (b) (c) (d)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a control system under test with constant velocity, the appropriate test input for steady-state analysis is (A) ramp (B) parabola C) sinusoidal (D) step
need urgent
For, z=0.05 and Wn= 10 : Peak amplitude = 1.85 Rise Time = 0.108 * Settling time = 7.6 seconds true False The peak time is related to the largest time constant of the control system True False For damping ratio greater than one, the rise time is considered as 10% to 90% of its final value True False
TUTORIAL PROBLEMS 2. A long shunt compound ganerator has full losd output of 100 kW st 250 volts. The armature, series and shunt windings bave rmistances of 0-05 ,0-03 0 and 55 respectively. Find the Brmature current and L A 4 oele shunt gmerstor with wave-wound armature has 41 alots, nch having 12 conductors. Th muture resistance is 0-05 and shunt field resistance is 200 . The flux per poie in 25 mWh. Ifa lond ce of 10 is connected soros the armabure ferminals, calculate the voltage scross the lond w mrior is driven at 1000 rp.m 389-5 V pmented emf 464-5 A, 282-3 V
Assume a flat start and calculate one iteration of Gauss-Seidel. SD₁ = 0.5+ j0.5 SD3 = 0.5+ j0.5 |V₂|=0.95 V₁ = 120 Z =j0.1 PG₂ = 0.8 V₂ = 120 SG SD SD3 SG₂ 2
Q2) Three shunt generators operate in parallel and supply a load current of 12000 A, connected across the bus-bars. Details of the generators are given below, Generator A Generator B Generator C Eg4 = 450 V EgB = 460 V = 410 V 0.02 N Raa = Ras = 0.025 A Rac = 0.01 %3D Egc a) Calculate the load voltage (bus bar voltage). b) Find the current supplied by each generator. c) Determine the output power (in Kw) for each machine
H.W-3 1- Why the capacity of SG is taken in kVA and for IM is taken in kW? 2- Explain the effect of changing the load (inductive-capacitive- resistive) on SG terminal voltage? 3- Why the magnetization curve of SG is similar to the B-H curve of armature steel core? 4-Write a short report about Blondel two-axis theory for SG?
how was the load 300<-36.86 achieved?
The block diagram of a mechanical transmission system shown in Figure Q11, where K is a positive gain. K (s+20) s(s+1)(s+10) Figure Q11
Draw the phasor for the synchronous compensator ateach of the following operating conditions: lagging pf, leadingpf, and normal excitation?
9.09 The flux density distribution in the air-gap of a certain generator is such that it contains a fundamental, a third harmonic, and a fifth harmonic. The flux per pole due to the fundamental distribution is 9 x 10-3 weber, that due to the third harmonic distribution is 0.9 x 10-3 weber, that due to the fifth harmonic distribution is 0.4 x 103 weber. There are four armature slots per phase per pole, the connection are made for three-phase wye. and the coil pitch is 12/15. The frequency is 60 cycles and the generator has 4 poles. (a) Calculate the emf/turn. (b) If there are six turns/coil and two coil sides/slot, calculate the emf per phase. (c) Calculate the emf between line terminals. Ans. 2.32V; 212V; 364V
A separately excited generator has no-load voltage of 125V. A certain load rated at 1200W, 120V is then connected at the terminal. Calculate the series resistance needed to connect to the armature circuit in order for the load to operate at rated condition if the armature resistance is 0.0692Ω.