If the mercury thermometer is used as a measuring device in a control system. What is the degree of it? And show how to reduce it's time constant? Then, if this thermometer having a time constant of (30 x 106 nh) is initially at (560 °C), it is immersed in a bath at (150 °C) at (t=0), determine the indicated temperature at (t =3.5 min). Also, if the thermometer is read a temperature at (t =4.5 min), and then is return to the initial bath, find what will be the temperature reading at (t =6.5 min)?

If the mercury thermometer is used as a measuring device in a control system. What is the degree of it? And show how to reduce it's time constant? Then, if this thermometer having a time constant of (30 x 106 nh) is initially at (560 °C), it is immersed in a bath at (150 °C) at (t=0), determine the indicated temperature at (t =3.5 min). Also, if the thermometer is read a temperature at (t =4.5 min), and then is return to the initial bath, find what will be the temperature reading at (t =6.5 min)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
(answer number 4-8 & main question) Two vessels of different shape and sizes are connected by means of a pipe with a valve. Vessel A has a diameter of 4 ft and the length is 1.8 m at the given pressure gauge of 1476.4 in Hg and temperature of 82°F. Another vessel spherical in shape contains the same gas at 15,000 torr gauge and 18°C. The valve is opened and when the properties have been determined, it is found out that the gauge pressure is 35.7 kgf/cm2 and the temperature is 21°C. If the barometric pressure is 755 mm Hg, find the following: Volume of Vessel A in in3 - done Pressure at Vessel A in psia - done Temperature at Vessel A in °R - done Pressure at Vessel B in psia Temperature at Vessel B in °R Pressure of the gas when mixed in psia Temperature of the gas when mixed in °R Atmospheric pressure in psi Main Question: What is the diameter of the spherical tank in inches if the gas is carbon dioxide?
A soap bubble of 2.5 mm diameter with a surface tension of 0.22N/m. Determine the inside pressure in the soap bubble in psi
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. An airplane has a half-wingspan of 31 m. Determine the change in length of the aluminum alloy [a = 24.0 × 10-6/°C] wing spar if the plane leaves the ground at a temperature of 17°C and climbs to an altitude where the temperature is -51°C. Answer: 6 = i mm
What is the difference between the hydrostatic pressure and osmotic pressure?. e 1:59 /
As shown in the figure, when the temperature was 20 ° C, a 0.5 mm gap was left. Just determine the approximate value of the Temperature (° C) needed to close the gap.
A device's outer cylinder diameter is 7" and its distance from outer cylinder to the inner cylinder is 0.0356". The said outer cylinder of the device is rotated at 242 rpm and produces a torque of 1.59 lbf-ft. Determine the viscosity of the fluid inside the concentric cylinders of the viscometer it its length is 4'. Express your answer in 7 decimal places and in lbf-s/ft2. (ANSWER MUST BE 7 DECIMALS)
- The system shown in the figure is used to accurately measure the pressure changes when the pressure is increased by AP in the water pipe. When (Ah 70 mm), what is the change in the pipe pressure. Glysa 50-13 D-10 do 3mm
Air at -100°F and a pressure of 50 psia has a kinematic viscosity of what?
The cylinder, which has a sensitively moving piston inside, is filled with V₁ = 0.93421 The temperature outside is T₁ = 8 °C and the air pressure is p₁ = 101 kPa The piston is quickly pressed into the cylinder, causing the volume in the cylinder to decrease to V3 = 0.2975 1 and the pressure to increase to p2 = 210 kPa. The piston is locked in place and the cylinder is immediately brought to the laboratory. After that, it happened that the gas temperature became same as the laboratory temperature of T3 = 22 °C Determine the gas pressure when the gas temperature has reached the final temperature of the laboratory. What is the algebraic expression for pressure in terms of V_1, T_1, p_1, V_3 and T_3 P3 = What is the pressure? P3 = kPa
A thermometer is being designed for a process in which the temperature varies from 0 to 180 °C; from experience it is known that the process temperature, when it gets out of control, reaches up to 240 ° C. Considering that only the bulb is in contact with the part inside the equipment, what should be the volume of the safety vial? It is known that the bulb has a length of 1.2 cm and a diameter of 0.5 cm; the capillary has a length of 20 cm and the scale of the thermometer is -10 to 190 ° C. Consider that the coefficient of volumetric expansion for mercury is 1.82×10−4 ° C− 1
Problem 2 For this problem, use the graph below, also given at the end of the notes on stress concentration. Determine the stress concentration factor in a 0.2 inch thick flat bar with two symmetric grooves (semi-circular notches) of radius 0.3 inches and width 2.6 inches. Use the graph in Fig. 2. 3.0 Nolched rectangular bar in lension or simple compression. a0 = F/A, where A = dt and is the thickness. 2.6 2.2 1.2 K, 1.1 1.8 1,05 14 1.0 0,05 0.10 0.15 0.20 0.25 0.30 rld Fig. 2