If the inputs X and Y vary with time as shown for the given circuit, which of the following describes the output Z? 1 Y 2 3 Time (ms) Time (ms) Y

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: First we should select the correct option for given instructions Value of each bit in word B3:3 will…

Q: During the execution of an OUT instruction, the /0/M signal will Go low. Tristate. Not be used. Go…

A: Io/M is an active low signal means it can be activated by providing thr low input

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A:

Q: 11. What is the count range of the Asynchronous counter shown below? T 12. CLK 30 30 SCLE 74LS76N…

A: Given counter is Asynchronous Counter because clk is given first flipflop and then output of first…

Q: Which of the following is NOT a measurement made by a BERT tester? O Bit error ratio O Errored…

A: Bit error rate testing, or BERT, uses specified stress patterns made up of a series of logical ones…

Q: A. Sin B. Cosin OC. addition D. division E. Tan OF. multiplication G. subtraction OH.A, B, C, D, E,…

A: We need to tell about whether the given statement is true or false. We need to select correct option…

Q: convert decimal number ranging from 0 to 9 into 4 bit binary and 4 bit gray code

A: If B4B3B2B1 represents the 4-bit binary number with B4 as the most significant bit (MSB) and B1 as…

Q: What is the device address used by the instruction OUT A4, AL

A: OUT is a mnemonic that stands for OUTput Accumulator contents to an output port whose 8-bit address…

Q: 3 Given the following AHDL code, explain how this code "debounces" a pushbutton. If a key is…

A: Given  AHDL program ro debounce a pushbutton. We need to explain how debouncing occur. Please find…

Q: art 4. Two Bit Wide 4 x 1 Multiplexer sing process INPUT_A INPUT_B OUTPUT_Y INPUT_C INPUT_D…

A:

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: We need to select correct option for given instructions .

Q: Draw a 2x1 multiplexer block diagram. Create the status table. Find the simplest form of circuit…

A: Requirement:The block diagram of 2x1 multiplexer.Status table. The simplest form of circuit output…

Q: * bit current ADC. 0000 represents 4 4mA and 0001 represents 5mA (the resolution is 1mA). To get…

A: This question is related to Analog to digital converters

Q: QUESTION 10 With reference to the instruction below, what will be the value of each of the bits in…

A: The destination of the CLR (clear) instruction has a value of bits. All of the bits in the…

Q: Assembly language: O is easier to program in than high-level languages. O All of these are correct.…

A:

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A:

Q: Use the schematic for our board to select the input signals on the I/O Memory selection hardware…

A: From the given options                                                       IO¯/M   =1  : operation…

Q: Convert between different number systems. Fill-in the table below Row 1 only: Decimal Binary…

A: We should know that all decimal numbers use of 10 digits which are (0, 1, 2, 3, 4, 5, 6, 7, 8, and…

Q: Design a Circuit to perform the following Operation.

A: Break the A+B-C operation in two parts as: A+B=S S-C For First Operation, Take Half adder to…

Q: You have used DEBUG to unassemble the following instructions. -U 0100 0108 1369:0100 B84365 MOV AX,…

A: The instruction is loaded at location 0106, the instruction takes two bits when the given code is…

Q: Choose the correct instruction that will send data to an I/O device. IN AL, 60 IN 60, AL OUT 60, AL…

A: Format of Instruction: Opcode Operand1, Operand2. Opcode tells about the what kind of task is to be…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.