If the flow rate of water through the pipe system shown in the following figure is 0.050 m^3/s under total head loss of 9.0m, assuming a C coefficient of 120 for all pipes determine the following A.The head loss in pipe B Choices: 1.975m,4.465m,2.560m,5.886m B.The flow in pipe B in m^3/s Choices: 0.019,0.034,0.029,0.023 C.The diameter of pipe C

If the flow rate of water through the pipe system shown in the following figure is 0.050 m^3/s under total head loss of 9.0m, assuming a C coefficient of 120 for all pipes determine the following A.The head loss in pipe B Choices: 1.975m,4.465m,2.560m,5.886m B.The flow in pipe B in m^3/s Choices: 0.019,0.034,0.029,0.023 C.The diameter of pipe C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(b). Figure 1 shows a reticulation system. Estimate the flow rate in each pipeline using Hardy-Cross Method and Hazen-William formula up to two iterations. Adopt Hazen-William coefficient, C, as 100. The lengths and diameters for pipes AB, BC, CD, and AD are as follows: Pipe AB: length = 950 m and diameter = 250 mm Pipe BC: length = 750 m and diameter = 200 mm Pipe CD: length = 750 m and diameter = 200 mm Pipe AD: length = 900 m and diameter = 250 mm 40 L/s 40 L/s C B D Figure 1: Reticulation system 50 L/s 130 L/s
64 Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand and consumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply line section having diameter of Y cm. Assuming coefficient of friction factor f=0.00155. 19.2 lowrate) and Y (Diameter) from following table
Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the head loss through the network. Pipe 1: D₁ = 450mm, L₁ = 800m Pipe 2: D₂ = 400mm, L₂ = 700m Pipe 3: D3 = 500mm, L₁ = 600m 15.2m O 24.4m O 28.3m O 22.2m
answer is given just give the solution and right answer.
Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the volumetric flowrate in Pipe 1. Pipe 1: D₁ = 450mm, L₁ = 800m 1 Pipe 2: D₂ = 400mm, L₂ = 700m L2 Pipe 3: D3 = 500mm, L₁ = 600m O 0.69m^3/s O 0.78m^3/s O 0.46m^3/s O 0.63m^3/s
I need an answer quickly please
The total discharge (flowrate) from A to B in the figure below is 300 liters/s. Pipe lennthe are: L1= 150 m, and L2 = 450 m. Diameters, are: D1 = 500 mm, and D2 = 250 mm. L1:D1 Q1 Q Q2 L2; D2 Determine [Using Darcy's equation] the headloss [m] and the flowrates (/s] across A-B in pipes 1 and 2 if riyated steel iron pipes are used in the system and flow is FULLY TURBULENT. Flowrate pipe #1 [I/s] =- Flowrate pipe #2 [l/s] =- Headloss pipe #1 [m] =. %3D Headloss pipe #2 [m]
Homework 2 Water flows at a velocity of 1.8 m/s in a 150 mm diameter pipeline as shown in figure. At a particular section, the (gouge) pressure is equal to 150 kPa, and downstream of this section, the pipe elevation Increases by 1.2 m and the water is discharged through a 50 mm nozzle. Estimate the head loss between the section where the pressure is 150 kPa and the section is just downstream of the nozzle discharge. 1.8 m/s 150 kPa. 9 Pipeline 150 mm 1.2 m Nozzle 4 50 mm
Kindly do not give copied or wrong solution.
Water is designed to flow in a HDPE pipe of length 267 m as shown in the figure in Problem 10. The flow velocity is limited to 3.3 m/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter and the flow rate.
3) An incompressible flow velocity field is given as 1 1 [m/s] r r where r is in meters. (a) Calculate the mass flow rate through the cylindrical surface at r =1 m from z = 0 to z =1 m as shown in Figure A (b) Show that mass is conserved in the annular control volume from r = 1 m to r = 2 m and z = 0 to z = 1 m as shown Figure B a 2 m. I m 1 m 1 m 1 m