If the equation of a velocity profile over a plate is m/s at a distance y meters above the plate, dete y35cm. Take u= 84 noise

Q: How important is to follow the scheduled maintenance for the propeller like for overhaul inspection,…

A: overhaul inspection and annual inspection of the propeller

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: Multicylinder pump

A: Where more than one cylinder is being driven by one driver, the arrangement is named according to…

Q: Single Engine Failure while Hovering

A: Single engine failure while hovering is a critical situation for any helicopter pilot. It requires…

Q: Write the monthly maintenance schedule or chart for compressor propeller

A:

Q: an be manufactured by cast aluminum alloy only.  a. Nose Section b. Power Section c. Supercharger…

A: we have to determine which of the sections of radial engine can be manufactured by aluminum casting

Q: Briefly describe the definition of hydraulic radius.

A: HYDRULIC RADIUS…

Q: C- Mention three of the advantage of the positive displacement pump?

A: The question given is

Q: C- Mention three of the advantage of the positive displacement pump?

A: Given Data- Positive displacement type pump given We have to write Three advantage of Positive…

Q: What is the main difference between a crankshaft and a cam shaft

A: What is the main difference between a crankshaft and a cam shaft   Crank shaft is the shaft which is…

Q: 40. Worn cylinders can be reconditioned by-- a. None of the below b. Machining in the lathe c.…

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: 1.Name type of failures in engine blocks

A: The engine is the most important part of the IC engine. In production, Every company produces an…

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: G. Brake shoes Energy of motion H. Brake pads Operates the brakes on opposite comers of the vehicle…

A: Match Of the following  ****As per company policy we are supposed to do only three subparts if you…

Q: Technician A says that coolant hoses should be squeezed to check for hardening or softening.…

A: Solidly squeeze both the upper radiator and radiator hoses. They ought to feel firm, solid, and…

Q: Identify the point to be considered while maintenance of wiper pads on lathe machine Regularly…

A: To find: what point to be considered while maintenance of wiper pads on lathe machine.

Q: A- List three differences between the dynamic pump and peristaltic pump?

A: Given question: List three differences between the dynamic pump and peristaltic pump.

Q: What is Extensometer?

A: The extensometer is the measuring device that measures the change in length of the object. It is…

Q: What type of simple machine is a wheelbarrow? lever inclined plane O wedge screw

A: A machine used to reduce the effort while performing a task is called a simple machine.

Q: Task 5 - Brake Callipers and Discs Brake callipers and discs, like the braking system are different…

A: given; (1) examine the example caliper  and examine the material used? (2) How many piston are used…

Q: Which of the following situations will make a pump noisy? Select all that apply. O Excessive oil…

A: Answer:- All given situations will make the pump noisy.   The various situation that will make the…

Q: Explain rotating a wheel.

A: The motion of a circular object rotating around its axis is referred to as rotating a wheel. The…

Q: What do you mean by intake stroke?

A: Intake stroke: It occurs when suction occurs due to downward movement of piston in an internal…

Q: List four possible causes of cluth slippage

A: A Clutch is a mechanical device used in vehicles that transmits power from the motor to the…

Q: When pressurized fluid enters the cap end of a double-acting cylinder, the rod will retrac

A: GIVEN DATA - A MCQ GIVEN ABOUT DOUBLE ACTING CYLINDER

Q: C- Mention three of the advantage of the positive displacement 4 pump?

A: Given Data- Positive diaplacement pump given we have to list out its three advantage

Q: Wind Turbine Gearbox & Brake

A: In a wind turbine, a gearbox is used to transfer rotational speed from a low-speed rotor to a…

Q: A kick is defined as an unplanned formation fluid entry into the wellbore annulus. a. True b. False

A: A kick tends to occurs in  oil well when the pressure exerted by the rock surrounding the bore is…

Q: Explain principal of hydraulic?

A: Hydraulic system is work on the Pascal law. According to this law pressure in a closed container is…

Q: design of diaphragm pumps maintenance and replacement

A: Given Diaphragm pumps To find Maintenance Replacement

Q: xplain the different fluids or systems in an aircraft that needs fluid lines?

A: Multiple fluids are in action in an airplane : fuel hydraulic oil lubricant cooling oil water air

Q: Rotary pumps are suitable for handling oils Oa False Ob True

A: Rotary pumps are suitable to handle vicious and abrasive fluids like oil.

Q: Capsule is used for measuring flow rate. a. False b. True

A: Capsule is used for measuring flow rate. Answer: a) False

Q: One side of the pump is connected to the tank and the other hydraulic machine. True False

A: given = true or false

Q: Introduction to pneumatics

A: Pneumatics: It is the branch of science and technology of pressurized air—using piped, compressed…

Q: Which type of oil ring is slotted so that excess oil canpass through it?a. Cast ironb. Segmentedc.…

A: A compression ring is the seal that keeps leaks from pipe segments with a bell-shaped orifice at…

Q: Initially, the gas pressure is greater than the outside atmospheric pressure. When valve 1 is…

A: In this scenario, we have a system where the gas pressure is initially greater than the outside…

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: appliication of flash, fire, and pour points of lubricants and fuels

A: Flash point: It is the lowest temperature at which the given liquid provides sufficient vapor to…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.