If the coef. of discharge of the Venturi meter in Fig. 8-50 is 0.92, determine the actual discharge in lit/sec.

Q: Determine the discharge of a flowing fluid from a nozzle, whose specific gravity is 1.3, the nozzle…

A:

Q: Determine the headloss from A to D in the system shown in fig. 3 if the discharge is…

A: To find the head loss from A to D

Q: Q21: indicate if the flow fields are irrotational then determine the velocity potential and the…

A: A).   Given, u = x(1 + y), v = 12x2 - 12y2 - yWe know that, ωz = 12∂v∂x - ∂u∂yIf ωz ≠ 0, then flow…

Q: A sharp edge orifice 105-mm diameter, in the side of a tank having a horizontal cross-section 2m…

A: d=105mm H2=2m Cd=0.6

Q: Determine the discharge at pipeline 1 in lit/sec assuming f=0.02 for all pipes. CHOICES: a. 782, b.…

A: The problem is based on the parallel combinations of pipe flow. In this combination the head loss in…

Q: 1. Three pipes of different lengths and diameters connected in series as shown discharges 169…

A:

Q: A discharge of 100 L/s to be measured by triangular notch of vertex angle 60°. What would be the…

A:

Q: The theoretical discharge "Qt" can be computed by multiplying the actual value by the coefficient of…

A: Incorrect

Q: Problems (5.2) Figure below shows a conical vesse! having its outlet at A to which a U-tube…

A:

Q: How to calculate discharge through a venturimeter if the outer and inner cross-sections are given,…

A: Given: Outer cross-section = A1 Inner cross-section = A2 Difference in the height of manometric…

Q: Flow Measurement Question Two small circular orifice of diameters d₁ and d2, respectively, are…

A: Given data- Two small orifices- Diameters = d1 & d2. Depths of tank h1=25 cm & h2=1 m=100…

Q: Date Determination of Discharge Using a Venturi Meter tamula: Vol. %3D も PZ 29 trial #1 trial #2 H…

A:

Q: Compute the actual discharge from a standard 5 cm diameter orifice under a head of 3 m of water if…

A: This question is related to Fluid Mechanics. In this problem we calculate Actual discharge from…

Q: n testing a fire pump, it is desired to flow 500 gpm (1890 liters per minute) from a 1 3/4-inch (45…

A:

Q: Probiem 5: A liquid of specific gravity 1.7 flows in a 60-millimeter horizontal pipe. The total…

A:

Q: P.7.5 Find the throat diameter of a Venturi meter when fitted to horizontal pipe 10 cm diameter…

A:

Q: The velocity of flow in a channel is found by (a) Current meter (c) Pitot tube (b) Float (d) All of…

A: Current meter , pitot tube , float all these three instrument are used to find velocity of flow in a…

Q: discharge of a flowing fluid from a nozzle, v

A:

Q: 300 mmø 150 mmø Hgi13.6)

A:

Q: Determine the discharge at pipeline 2 in lit/sec assuming f-0.02 for all pipes. 700 m 450mm diam.…

A:

Q: 200mmø 690mm 300mm 400 mmø LHg (13.6) A 200mm diameter venturi meter is installed in a 400mm…

A:

Q: 7. A cylinder of radius 0.661m is rotated about its axis at 261 rev/ min. If the cylinder is 16.1%…

A:

Q: In the figure below, water at 20 degrees Celsius flows steadily through the piping junction,…

A: Reference : Fluid mechanics , Uniform Shower flow We need to find exit velocity that is velocity…

Q: .2. Н20 y1 20 сm Hg

A:

Q: Calculate the discharge through the submerged orifice shown in the figure. Ans: 109 lit/sec 50 kPa…

A:

Q: .. 300 mme 100 mmø H20, 2) 500mm Zng(13.6) 100m n dian oter ic instal ed in a 200m m diamn ots…

A:

Q: CALIBRATION OF V-NOTCH I want full calculations and graphs for that ASAP PLZ  Graphs (i) Qa Vs…

A: Given data, θ = 90o

Q: Under a head of 4m what is the coefficient of discharge if the actual flow is .003cu.m per second…

A:

Q: A discharge of 100 L/s to be measured by triangular notch of vertex angle 60°. What would be the…

A:

Q: Question 2 Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above…

A: Given:-  Discharge in pipe = 30 l/s = 0.03 m3/s  Diameter of pipe = 30 cm = 0.3 m  Elevation above…

Q: A vertical circular cylindrical tank 3.0 m diameter contains water. If the surface is 7.0 m above 10…

A:

Q: A discharge of 100 L/s to be measured by triangular notch of vertex angle 60°. What would be the…

A:

Q: A U-tube with uniform legs and both open to the atmosphere has its bottom portion contains mercury…

A:

Q: Question 2 The discharge Q over a V-shaped notch is known to depend on the angle of the notch, the…

A: It is given that Q=..................1Total number of variables=5Total number of fundamental…

Q: 5-7E A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the…

A: Given data,(d1)=Inner diameter of hose =1 in(d2)=Diameter at the exit of nozzle= 0.5 inV1= average…

Q: 2. A venturimeter is used to determine the flow of water through the reading of a manometer…

A: The relationship between pressure drop and flowrate is given as:…

Q: Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water…

A:

Q: The Best Efficiency Point is the point in a pump curve that coincides with its maximum flow rate.…

A: The performance curve depicts how such a variation from BEP, such as operating mostly on the left or…

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.