I RevievPart AIf the allowable tensile stress for the bar is(0t)allow = 22.6 ksi, and the allowable shear stressfor the pin is Tallow = 12.2 ksi. Assume the hole inthe bar has the same diameter d as the pin. Taket = 1/4 in. and w = 2 in. (Figure 1)Determine the diameter of the pin so that the load P will be a maximum.Express your answer to three significant figures and include appropriate units.HÀ?d =ValueUnitsSubmitRequest AnswerPart BWhat is this maximum value for P?Express your answer to three significant figures and include appropriate units.Figure1 of 1HA?w/2P =ValueUnitsw/2SubmitRequest Answer

Answered: Image /qna-images/answer/f1043a50-0580-4ed4-bce8-a1f651a7f2c3.jpg

If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t= 1/4 in. and w = 2 in. (Eigure 1)

If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t= 1/4 in. and w = 2 in. (Eigure 1)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
What is the maximum possible value of the clamping Force C in the jaws of the pliers shown in the figure if the ultimate shear stress in the 5-mm diameter pin is 340 MPa? What is the maximum permissible value of the applied load P to maintain a factor of safety of 3.0 with respect to failure of the pin?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?