Answered: If steel with a 228 MPa yield strength…

If steel with a 228 MPa yield strength is used for a cold-formed shape,what would be the approximate yield strength of the deformed corner aftercold-forming?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.13P

See similar textbooks

Related questions

Q: Considering a finite cylinder of single crystal aluminum with a diameter (D) that has an axial unit…

A: The values provided are as follows:- A finite cylinder of single crystal aluminium with a diameter…

Q: A single crystal of BCC iron is subjected to tensile stress of 100 MPa along the [001] direction.…

Q: If design bond stress = 1.5 N/mm² is assumed, then the development length of an Fe 500 HYSD bar of…

Q: Calculate the maximum force that a 2.5mm thick and 50mm wide nickel strip, having a yield strength…

Concept explainers

Crack Detection

Concrete materials are meant for supporting structures, building foundations and they act as several load-bearing structures. Over time, due to environmental conditions, and based on the constituent materials used, concrete materials are subjected to a great degree of distress. Corrosion of the reinforcement bars due to chemical influences, uneven base, earthquake, drying shrinkages, and alkali-aggregate reactions are some of the reasons for concrete distress.

Question

If steel with a 228 MPa yield strength is used for a cold-formed shape,
what would be the approximate yield strength of the deformed corner after
cold-forming?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1:The given data is:

VIEW

Step 2: yield strength of the deformed corner will be:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation? Select one: Oa. 133.5 MPa, yes O b. OC. Od Oe. 120.5 MPa, no 129.5, yes 140.5, no 123.5 MPa, yes
Calculate the maximum force that a 2.5mm thick and 50mm wide nickel strip, having a yield strength of 310 MPa and a tensile strength of 430 MPa, can witstand with no plastic deformation.
6)
If a steel with a 33ksi yield strength is used for a cold-formed shape, what would be the approximate yield strength of the deformed corner after cold-forming?
A copper rod is deformed using a uniaxial tensile force of 16000 N. Deformation continues until sufficient strain hardening has occurred such that the applied force is too small to allow further deformation. After deformation, the rod has a diameter of 0.01 m and a length of 1.5 m. Assume that copper follows the strain hardening lawwith K of 310 MPa and n=0.54 Please calculate the true strain after the deformation ?
A cylindrical specimen of cold-worked steel has a Brinell hardness of 240. If the specimen remained cylindrical during deformation and its original radius was 11.8 mm, determine its radius after deformation. For steel, the dependence of tensile strength on percent cold work is shown in Animated Figure 7.19b. i mm
A laminated [0/90/0/90]s graphite/epoxy beam is 1 mm thick, is 20 mm wide, and has 0.125 mm thick plies. The lamina properties are E1 = 180 GPa, E2 = 10 GPa, ν12 = 0.28, G12 = 7 GPa Xt = 1700 MPa, Xc = 1400 MPa, Yt = 40 MPa, Yc = 230 MPa (a) Determine the flexural modulus of the beam (b) How could the flexural modulus be improved without changing the ply materials, the number of plies, or the ply orientations? (c) Using the Maximum Stress Criterion for each ply, determine the magnitude of the maximum allowable bending moment that the beam can withstand. Which ply fails first?
i need the answer quickly
A structural component in the shape of a flat plate 24.3 mm thick is to be fabricated from a metal alloy for which the yield strength and plane strain fracture toughness values are 533 MPa and 22.0 MPa-m1/2, respectively. For this particular geometry, the value of Y is 1.3. Assuming a design stress of 0.4 times the yield strength, calculate the critical length of a surface flaw. What formulas do i use ? And how do i use them?
Mechanical Properties-Metals For a bronze alloy, the stress at which plastic deformation begins is 295 MPa and the modulus of elasticity (E) is 108 GPa. (a) What is the maximum load (Fy) that can be applied to a specimen having a cross-sectional area of 314 mm2 without plastic deformation? (b) If the original specimen length is 142 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
Two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing their cross-sectional areas (while maintaining their circular cross sections). For one specimen, the initial and deformed radii are 15?? and 12??, respectively. The second specimen, with an initial radius of 11??, must have the same deformed hardness as the first specimen. Compute the second specimen’s radius after deformation.
A single crystal of BCC iron is subjected to tensile stress of 100 MPa along the [001] direction. Which of the two slip systems ((211) –[ 111 ] or (321)–[ 111 ]) is going to yield first?