2 leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potentthe motor in that direction, causing the motor to spin.O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction.Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2.D2YellowR150 QR250 0R3PSB (+5 V100 aLWR4D1100 QBlueSW1Sw2Question 2本 If neither switch is closed, is there a potential difference across any of the circuit components?[ Select ][ Select]Yes, but only the switches.Yes, there is a potential difference across the LeDs, because there is an additional resistor on one side.Yes, across all of the components, but that difference is less than the minimum forward voltage of those components, so the LEDS do not light and the motor does not turn.No

In the question, 2 switches are consist in the circuit. If neither switches closed, is there a…

If neither switch is closed, is there a potential difference across any of the circuit components? [ Select] [ Select] Yes, but only the switches. Yes, there is a potential difference across the LEDs, because there is an additional resistor on one side. Yes, across all of the components, but that difference is less than the minimum forward voltage of those components, so the LEDS do not light and the motor does not tu No

If neither switch is closed, is there a potential difference across any of the circuit components? [ Select] [ Select] Yes, but only the switches. Yes, there is a potential difference across the LEDs, because there is an additional resistor on one side. Yes, across all of the components, but that difference is less than the minimum forward voltage of those components, so the LEDS do not light and the motor does not tu No

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3.Calculate YT and ZT
A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.12 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 135KV. Find the Voltage distribution across each unit and the String Efficiency
In a string of suspension insulator with three units,the line unit has 12k and k=0.15. The voltage across string is and the efficiency is .?: a. 41.6kV & 69.4kV b. 33.62kV & 74.7% C. 29.52kV & 82% d. 36.9kV & 82%
The loads on a 300-meter ring distributor are depicted in figure 2.1 (a), where the distances are given in metres. Each conductor has a resistance of 0.20 per 1,000 metres, and the loads that are tapped off at points B, C, and D are as shown in the diagram. Determine the voltages at B, C, and D given that the distributor is fed at point A. 50 A 70 1 240 V A (a) 60 B 70 A 100 A 80 50 A 91A D T 41 A 220 V A (b) 129 A B 100 A 729 A 70 A
write the factor governing height of pole
A) Explain earthing and its importance in electrical installation. BÍ With a help of a labelled diagram a single phase supply, differentiate between TN-S earthing system and TN-C-S system. C Calculate the earthing resistance of an electrode given its length is 4 dm and its radius of 1 cm if the resistivity of the soil is 50 ohms. D) From the result obtained in the question 2(C), calculate the earth resistance when two similar electrodes are in parallel. Explain your answers.
14. For a power plant with two units, the weekly load is 1200 MW. The coal consumption (tons/hour) for each unit is Q₁ 16+.3P₁ tons/hours Q2-25+.4P₂ tons/h The total coal available to the plant is limited to 90,000 tons/week. If the linear cost curves are given as C₁=495+11P₁ $/hour, C₂-760+10P₂ $/hour And generation by each unit is limited to 150 ≤ P, ≤ 600MW Determine the values of P₁ and P₂ for minimizing the cost of power generation. 15. Use LP to determine economic dispatch if C₁ = 5+ 3P₁, C₂ = 7+6P2, C3 = 8 + 9P3 50 P₁ < 150 MW and PD=210 MW If the line flow P12= .3P₁ + .4P₂ + .1P3, also determine P₁, P₂ and P3 so that P₁2 is limited to 70 MW. 1 4 400 ≤ P₂ ≤1000MW H 2 3
Scenario: You work as a materials engineer and have been tasked with investigating issues with substandard cables manufactured by your company. These cables are made from copper with varying cross sectional areas depending upon their current carrying capacities. Cables are not meeting the required voltage drop characteristics compared to theoretical values, but your manager is not sure of the reason for this and has hypothesised that this could be due to impurities within the copper itself. It has been suggested that the resistivity of the copper used should be investigated. With reference to the attached samples picture: A) what is the actual resistance of the cable samples. given that you multiply the cross sectional area by strand number. B) what is the actual resistivity of each sample.
Q2/B: A grading string of four insulators has a uniform voltage across each disc. The capacitance of each pin to earth is C. The capacitance of the top unit is 5 C as shown.(a) Calculate the capacitance of the remaining discs, (b) If the voltages of units one and two are 60% and 40% of line voltage.,Calculate other voltages and string efficiency.
21. A piece of wire that is one mil in diameter and one foot long is one mil-foot. Select one: TRUE FALSE
21 Balance is obtained in a DC potentiometer at a length of 71 cm when using a standard cell of 53.2 volts. Calculate the EMF of a dry cell if balance is obtained with a length of 20 cm. a. 0.07 b. 14.99 c. 0.01 d. 188.86
MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanks