If it is known that the center pin A supports one-half of the vertical loading shown. Determine the magnitude of the force (in kN) in members AB, BF, and CD. Include the negative sign if the member is in compression. Use the method of joints. If it is known that the center pin A supports one-half of the vertical loading shown.6 panels at 12 mCED16 mHG,B12 mA10 kN 8 kN 8 kN8 kN 8 kN 10 kNDetermine the magnitude of the force (in kN) in member CD. Include the negative sign if the member is in compression.

Answered: Image /qna-images/answer/f49737ac-d957-411b-aead-0fd5dbe92005.jpg

If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12 m C E D 16 m H G, B 12 m A 10 kN 8 kN 8 kN 8 kN 8 kN 10 kN Determine the magnitude of the force (in kN) in member CD. Include the negative sign if the member is in compression.

If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12 m C E D 16 m H G, B 12 m A 10 kN 8 kN 8 kN 8 kN 8 kN 10 kN Determine the magnitude of the force (in kN) in member CD. Include the negative sign if the member is in compression.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 410 mm2 and a length of L1 = 3.2 m. Rod (2) has an area of A2 = 355 mm2 and a length of L2 = 1.3 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 50 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) L2 a B C D x,u Rigid bar |(1) Answer: (a) o1 = i MPa 02 = i MPa (b) VD = i mm
1.5 m L E 2 t t T t A -2 m 3 kN D B 2 m Determine the force in each of the truss members using method of joints. Draw all pertinent free-body diagrams and indicate tension or compression for the internal forces. Identify any zero-force members.< C I=
D В a 2 m A F -2 m- - 2 m- -2 m- 1000 N Use the truss from Problem #1below to determine the force in each member Mention whether the members are in Tension (T) or Compression (C). Use the Method of Joints to analyze the truss. (20- points)
The control arm is subjected to the loading shown. The allowable shear stress for the steel pin is τ = 10 ksi. Determine the required diameters of the steel pins at A and C. Write your final answer to the nearest three decimal places.
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 2240 N, a = 3.3 m, b = 6.6 m, 0 = 47° Answers: AB= AC = B AD = Ꮎ Jak a Ө b Ꮎ N Z Z N N D F
1. Use the method of sections to determine the internal forces in members BC, GC, and GF. The structure is supported by a pin at D and a roller at E. A -2 m- 1000 N B G a a -2 m- C F -2 m- E 2 m
Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F = 7.5 kN, a = 2.5m, b = 3 m, c = 2 m, and d = 2 m. A F Answers: BE= BD = a i i B b E a b O KN KN
Problem 2: Determine the forces in all diagonal and horizontal members of the truss shown below using the method of sections. Determine the force in all vertical members using the method of joints. Hint, the structure is symmetric. The distributed load is transferred to the truss from the roof purlins. State whether the members are tension or compression. Summarize your results on a sketch of the truss. 2.5 k/ft H M K 12 ft A G B C D F 6 @ 12 ft = 72 ft
Consider the truss shown in (Figure 1). Set P₁ = 8 kN, P₂ = 10 kN, and P3 = 6 kN. Figure E ZA B C 3m P₁ P3 3m < 1 of 1 P₂ -3m- 3m D. ✓ Correct ▼ Part D Determine the force in member BF of the truss and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBF = 7.67 HA kN Submit Previous Answers Request Answer ? Review * Incorrect; Try Again; 5 attempts remaining
For the truss shown in Figure 2.3b, determine the force in member KP if x = 5 m, y = 7 m and P = 7.94 kN. Indicate whether the member is in tension or compression. (Note: Use negative sign (-) if the member is in compression.) 7 panels at x m = 7x m В J D K L y F A х М N H G P P kN P kN
Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299
1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in the figure. Determine the average normal stress developed in each member when the truss is subjected to the load shown. State whether the stress is tensile or compressive. -0.6 in. AAC -3 ft- Auc= 0.8 in.2 AAB 1.5 in. 500 lb B