If in a single phase full wave AC voltage controller, the firing angle of the SCRS are equal, then the rms output voltage will be Positive Zero Negative None of the given options

Q: What is condition-based maintenance? Explain the following two methods of condition monitoring in…

A: Step-1-> Condition-based maintenance (CBM) is a maintenance strategy that focuses on monitoring…

Q: と。 O/ A balance 2-phose Y-Comecled \aad has z to 4-usa on Find phose Curents and live cnnnts.

A: Given data, Phase impedance is given, Zph=10∠-450 VCA is the voltage between line C and A therefore…

Q: 2. Two trausformes A and B of ratings 5uokVA.and 25okl; Supplying a load kVA of 750 ato.8Pt lagginy.…

A: Ans (a)

Q: For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 Ybus…

A: In this question we need to find a voltage of bus 3 after two iteration

Q: Calculate the average and the root-mean-square value of the output voltage for the network in the…

A: Given circuit is full wave rectifier , we know formula for average value and RMS value for full wave…

Q: The avalanche breakdown occurs at a lower voltage compared to zener voltage. True False

A:

Q: The sequence components have same voltage magnitude.

A: This problem is based on the sequence components

Q: Which of the following is not a boundary condition for an SLG fault on phase 'a' of a power system?…

A: Since the single line to ground fault occurs on the phase a of the system the fault current of phase…

Q: The system values  are given below.  The bus 1 voltage after fault  = 1.5 p.u  The bus 2 voltage…

A: The bus 1 voltage after fault = 1.5 p.u  The bus 2 voltage after fault = 1.2 p.u The line admittance…

Q: Draw the circuit diagram and explain the operation of power factor improvement by using (i)…

A:

Q: 7. (30cis87.6)/24cis48

A: The question is about polar form.

Q: Add 398Bcd to 269BCD Showing carries and digit corrections

A: The BCD representation of the number 398 is,  3: 00119: 10018:1000398BCD=0011  1001  1000 The BCD…

Q: Why 'during fault' do we use the transferred reactance of (X_12) 1.8 to calculate P2 Max. Why do we…

A: The question is about calculating net impedance during fault.

Q: bon grob Bone & ho ghume asi 100 a.7) Which of the following characteristics usually represents an…

A: .                              SOLUTION                                   PART-7 ANSWER Higher Power…

Q: a) Derive the formula for total voltage and impedance for series RL circuit. Find the equation of…

A: Diagram of series RL circuit is given by,

Q: n phase margin why the phase go down for first time then go up?

A: As electronic amplifiers the phase margin (PM) that is the difference between the phase lag φ (<…

Q: For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2…

A:

Q: Determine 71000  mod 6 and  61001 mod 7

A: Determine 71000 mod 6 and 61001 mod 7 ?

Q: Increasing will cause the rise time to decrease and reduces steady state error, but increases…

A:

Q: Why load characteristics goes lower with respect to the occ

A:

Q: Design a synchronous counter which count in the followin sequence 1,2,3,4,5,6 then repeat using…

A: According to the question we have to Design a synchronous counter which count in the following…

Q: Determine the symmetrical fault in each bus as shown in figure.  Assume all pre-fault voltage to be…

A: To determine the symmetrical fault currents at each bus in the given 4-bus power system, we will…

Q: 09.5

A: option 2 is correctExplanation:  Thank you

Q: The algebraic sum of current leaving and entering in any closed loop is zero. A True B False

A: To state whether the given statement is true or false.

Q: The zero sequence components are with each other.

A: Zero sequence components Phase sequence?

Q: 1. Perform the following steps for the given circuit in below. RD = 1.8k2, Rs = 5602, RG = 2.2M2,…

A: D) as for all the above cases  Vds>Vgs therefore it is saturation as for first case Vds=8.66 v…

Q: The minimal cut sets for a series system is always a lower bound on Reliability. True False The…

A: The minimal cut sets for a series system is always a lower bound on Reliability. True False The…

Q: Problem #2: Draw the circuit of a synchronous MÓD-6 up counter.

A: Synchronous Mod 6 Up counter:                It contain six counter states while designing the Mod-6…

Q: The Full-load and No-load of a regulator are 5.2V and 5.3V, respectively. Then the % load regulation…

A:

Q: A11 e generators are classified according to the methods of their field excitation. (TRUE/FALSE)

A:

Q: 4) Reduce the block diagram of the system using Mason's Rule. Rist Dy Xx(x) -26 -24

A:

Q: Closed-loop system is strongly influenced by the presence of disturbances, and it needs calibration…

A: Introduction Closed-loop system: A closed-loop system is a type of control system that utilizes a…

Q: For the system shown in figure obtain the positive sequence, negative sequence and zero sequence bus…

A:

Q: False True the slip-rings replaced by separated segments In order to generate a bidirectional…

A: "The slip rings replaced by seperated segment in order to generate a bidirectional voltage" This…

Q: Design a sequence generator to the prescribed sequence 0111110

A: Aim- to design a sequence generator of sequence 0111110.   Thus length of code is(L)=7    Let number…

Q: Complete the general root-locus drawing graph according to the open-loop poles and zeros given…

A: We need to draw root locus for given pole zero plot .

Q: Consider the circuit below. Find the value of mesh currents in its designated loop where all loops…

A:

Q: This configuration can overcome the disturbances. Close-loop System Open-loop System Closed-loop…

A: Definition: The expression  control system is a set of mechanical or electronic devices that…

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.