If each cable can sustain a maximum tensile stress of 210 MPA before it fails, determine the greatest mass of the box the cables will support in the position shown. The cross-sectional area of the cable is 100mm2.

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

A:

Q: The homogeneous bar shown below is supported by a smooth pin at C and a cable that runs from A to B…

A: Free Body Diagram of the given assembly:

Q: P=75KN e=200mm 200 mm 20 mmo 200 mm

A:

Q: DETERMINE THE AVERAGE PUNCHING SHEAR STRESS THE CIRCULAR SHAFT CREATES IN THE METAL PLATE THROUGH…

A:

Q: For the truss shown, calo member BD. The cross-se member is 1200mm². A 6m C 4m E

A:

Q: P= 78KN 100 mm 400 mm 20 mm

A:

Q: Refer to the photo provided and please make sure your handwriting is readable. Given E = 200 GPa and…

A: PB = 80KN

Q: The center of gravity of the 800N highway sign is at point G. It has been determined that it can…

A:

Q: A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig. P-105. Calculate…

A: in this problem by using  area=force/stress we get smallest area because if area will be more than…

Q: • 6-E • A combination beam is constructed by welding a 1/2" x 6" flat bar on the top and bottom of a…

A: The moment capacity of a beam,Moment capacity = Tensile force in steel * Moment armThe tensile force…

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point…

A:

Q: Determine the largest weight “W” that can be supported by the two wires AB and AC. The working…

A:

Q: 2. What is the maximum bending moment that can be applied to the section without causing tension at…

A: Given  Effective stress=600MPa b=275mm d=550mm

Q: E,4A E,A E,2A L 2P L 8P 10P

A: Hello dear this is the solution of your problem The strain in each member is found to be…

Q: 4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using…

A:

Q: The ends of the three cables are attached to a ring at A and to the edge of the uniform plate…

A: T = 11 kN We need to calculate largest allowable mass of the plate.

Q: A homogeneous 800 kg bar AB is supported at either end by a cable as shown. Calculate the smallest…

A: Calculate the smallest area of the bronze cable,Abr=?

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: Determine the tensions in cables AB, AC, and AD. 1.75 m 2.25 m C. 1.55 m 0.45 m B 2.3 AO 110 kg…

A:

Q: Determine the principal stresses acting at the 1 section using Mohr circle

A: Determine the area of the section. The area of the section is A A=150 mm5 mm+180 mm6 mm+200 mm8…

Q: Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following…

A:

Q: Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter…

A:

Q: The tower in Figure 1 is subjected to three compressive forces 4kN, 5kN, 6kN at joints G, E and C…

A: Calculate the stresses in MPa in members AC, CE and FD

Q: Situation No. 1 A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the…

A:

Q: BOLTED/RIVETED CONNECTION: SITUATION: In the figure, assume that a 20-mm-diameter rivet joins the…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: O O OO O o o W shape

A:

Q: ind the diameter of dAB BC вс + bar if the stress equal t .15GPA 120cm B 125kN 125kN 90cm A 60KN

A:

Q: Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving…

A: Given data in question  Torque 1.5 and 4 kNm Length 1.5 , 2 and 3 m Modulus of rigidity 28, 83 &…

Q: Question 7 The maximum compressive force acting on the hatched area of cross-section is 2 25 mm…

A:

Q: Calculate the shear stress in MPa at section B A 100 mm F=10EN 10 mm

A: Shear stress:- shear stress is defined as shear force per unit area.

Q: The tower in Figure 1 is subjected to three compressive forces 4kN, 5kN, 6kN at joints G, E and C…

A: P1 = 4KN P2 = 5KN P3 = 6KN

Q: A uniform bar AB weighing 500 kg is supported at both end by cable as shown in the figure below.…

A:

Q: 3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the…

A: fu = 3700kg/cm2 = 3700 x 10-2 kg/mm2

Q: The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average normal…

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.