ull OMANTEL08:47@ 83%A Ims.act.edu.omQuestion 3Not yet answeredMarked out of 1.00P Flag questionIf a magnet is held stationary and a coil ismoved towards the magnet with high speedthen,O a.Flux linked to the coil increases andhence there is an induced emfb.Flux linked to the coil decreasesс.Flux linked to the coil remains thesamed. There is no induced emf sincemagnet is at restQuestion 4Not yet answeredMarked out of 1.00P Flag questionThe significance of the negative sign in theequation of electromagnetic induction

As we move the coil towards magnetic, the magnetic field changes and hence induces an emf in the…

If a magnet is held stationary and a coil is moved towards the magnet with high speed then, O a. Flux linked to the coil increases and hence there is an induced emf O b. Flux linked to the coil decreases O c. Flux linked to the coil remains the same O d. There is no induced emf since magnet is at rest Question 4 Not yet answered Marked out of 1.00 P Flag question The significance of the negative sign in the

If a magnet is held stationary and a coil is moved towards the magnet with high speed then, O a. Flux linked to the coil increases and hence there is an induced emf O b. Flux linked to the coil decreases O c. Flux linked to the coil remains the same O d. There is no induced emf since magnet is at rest Question 4 Not yet answered Marked out of 1.00 P Flag question The significance of the negative sign in the

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

5- The bar magnet shown in the figure is moved completely through the loop. Find the direction of the current flow between the two points a and b in the circuit, if the magnet enters and the magnet leaves the loop. Motion Toward the Loop
6. At what speed must the sliding rod in the figure below move to produce an emf of 1.20 V in a 1.69 T field, given the rod’s length is 29.0 cm? THIS IS NOT AND WILL NOT BE GRADED
3
4. A student performs magnetic force experiment by using current balance setup below. A magnet of 36 g mass is balanced as the wire having 36 cm length and 2.6 A current on it creates magnetic force on the magnet. Calculate the magnetic field strength excerted on current loop. Current Loop Power Supply Ammeter 0-5A (Max.) Base Unit Magnet Assembly Fig. 1. Magnetic force experiment setup + 1
Question 4 A coil of 2000 turns rotates in Earth's magnetic field (magnitude 6.0 x 105 T). If the coil encloses an area of 25 cm² and rotates in 0.020 s from a position where its plane is perpendicular to Earth's magnetic field to one where its plane is parallel to the field, what is the average emf induced in the coil?
student experimenting with magnets turns a circular loop of wire of radius 4.0 cm from a horizontal position to a vertical position in between a 0.17-T horseshoe magnet Calculate the change in magnetic fux through the circular loop
Subject Electromagnetic2
A120.0V motor draws a current of 7.00 A when running at normal speed the resistance of the armature wire is 0.720 determine the back emf generated by the motor
Indicate the direction of the induced current in the loop while the current through the straight conductor is increasing. a) clockwise b) counter clockwise c) no induced charge d) not enough information
Please help with questions one and two
Imagine a long straight wire and above it is a circular loop of wire. If a current passing through the straight wire is increased, then the direction of the induced current through the circular loop is a.) clockwise b.) counterclockwise c.) no induced current d.) cannot be determined
4-The figure below shows four wires carrying currents that are perpendicular to the page (to the screen), where I1=1.0A, I2=2.0A, I3=3.0A and I4=4.0A. Four Amperian loops (paths) are also shown in the figure. Find the current running through each of the loops.