ie frame shown in the Figure is supported by a hinge at A and a roller at E. ompute the vertical components of the hinge forces at C as they act upon membe C in kN. P = 28 kN and x = 3.3 m. Write numerical value only and in 2 decimal аces. D 1.5 m B MATHalino. On em k1 m +1 m-

ie frame shown in the Figure is supported by a hinge at A and a roller at E. ompute the vertical components of the hinge forces at C as they act upon membe C in kN. P = 28 kN and x = 3.3 m. Write numerical value only and in 2 decimal аces. D 1.5 m B MATHalino. On em k1 m +1 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

There is a wooden beam AD, as shown in the figure below, the Flexural Rigidity of the beam section is constant EI: Q:Try to find the (vertical) displacement of point B after deformation.
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
The steel framework is used to support 200KPa load (slab) used for an office. Sketch the loading that acts along members BE and FED. A. Take a = 2m b= 5m %3D B. Take a= 3m b= 4m B.
All Elements have a fixed value of E and I. Do load modelling for 1 meter strip width in the water tank section of wwwwww www.www the system.Draw the M N T diagram of the entire system. n=47 6 m. A ΔΒ B 7 water 8 m D 2 m. 47ton 3 m. E 1/10
Olny need you to draw and label the element and nodes. Also identify the unconstrained and contrained degree of freedom
. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together. Assume the glue nas a perfect bond. The densities of the two wooden parts differ and are indicated on the figure. The figure is not to scale. y Pq = 900 kg/m %3D 17 mm P2 = 740 kg/m? 20 mm 150 тm Determine the a-coordinate I of the center of mass of the T-beam. 90 mm
The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the displacement of aluminum rod caused by the force P = 55.25kN. ALUMINUM L=4.25m A = 556mm2 E = 70GPA STEEL L= 3.25m A = 354mm2 E= 200GPA 3.56m 2.64m
Bar AB is rigid and is attached to the steel and aluminum rods as shown in the figure. Before the application of load P, the rigid bar AB is horizontal. Determine the vertical displacement (mm) of point C caused by the load P = 50 kN. A Aluminum L = 3 m A = 300 mm² E = 70 GPa k 3.5 m C P -2.5 m Steel L = 4 m A = 500 mm² E = 200 GPa B
Problem 5.2 The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b= 1 ft D -b 2b B E AG Check your work: FEF = 1.26 kips a a a a P
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?
Example 2: giveny(x, t) = 4sin3x cos2t , find 2 and at
1.1 Show your complete solution.