Identify the Process of Low pressure vapour to High pressure vapour conversion in Refrigeration cycle O a. condensation O b. vapourization O c. compression O d. expansion The evaporator pipes have more vapour than liquid per volume is called O a. liquid cooling O b. Air cooling O c. Dry expansion O d. flooded Identify the HCFC refrigerant_ O a. R12 O b. R134a O c. R11 O d. R22

Identify the Process of Low pressure vapour to High pressure vapour conversion in Refrigeration cycle O a. condensation O b. vapourization O c. compression O d. expansion The evaporator pipes have more vapour than liquid per volume is called O a. liquid cooling O b. Air cooling O c. Dry expansion O d. flooded Identify the HCFC refrigerant_ O a. R12 O b. R134a O c. R11 O d. R22

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two-phase pipe flow is the simultaneous flow of a gas (or vapor) and a liquid exhibiting ___________physical properties through the same pipe a. same b. fixed c. different d. constant
In a basic LiBr-water machine, the generator operates at 170 F while the evaporator is at 47 F. the absorbing temperature is 75 F and the condensing temperature is 88 F. Compute the HRR for these conditions.
Which of the following is not an assumption for the ideal vapor compression process? a.Isobaric heating in evaporator b.Isobaric cooling in condenser c.Isenthalpic throttling d.Isentropic expansion
17- Where does liquid ammonia change into its low pressure vapors? a. Absorbor b. Generator c. Condenser d. Evaporator Clear my choice
Variable refrigerant flow (VRF) systems modulate the volume of refrigerant that is pumped through the system. This allows? A. Lower operation cost B. Better operating efficiencies C. Matching system capacity to the load D. All the above
The following data are known for Libr-H₂O absorption system. The cooling capacity is 3.5 kW, generation temp. is 82°C, condenser temp. 40°C, evaporator temp. 6°C. Temp. of absorber is 34°C. Assumed saturation condition for strong solution entering generation, weak solution leaving generation and water vapor Leaving evaporator. Properties of solution or water at each point (p, t, h, x), Mass flow rate each point,(COP) act & (COP) tho, Relative COP and Energy balance for all cycle components.
A. Describe the four processes, which occur in the vapor-compression-refrigeration cycle that youtested.B. How did you figure out the enthalpy at the various entry / exit stages? (I know you lookedat the chart or table provided! I understand that you may have used interpolation.) I want you toexplain briefly how you determined, what principle(s) you used to determine the enthalpy at thevarious points.Sketch a p-h diagram. On this sketch of the p-h diagram you must sketch and show SOME constanttemperature lines, constant pressure lines, constant enthalpy lines, constant entropy lines, quality factorand other significant features of the p-h diagram to show your understanding of the p-h diagram. Labelx & y axis, indicate the units, indicate the critical point. Label various regions,
11- During the air washer operation the: a. wet bulb temperature remains constant Ob. dry bulb temperature remains constant c. humiditv ratio decreases Od enthalpy decreases
15. A commercial refrigeration system with a single suction line and multiple evaporators can maintan a different temperature at each evaporator by controlling and differing, A. crankcase B. evaporator pressure C. head pressure D. liquid line temperature ck valve is 21. A m cond S Owo iss pressure
1 The condenser can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 2 The evaporator can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 3 Which loop is eliminated in a direct expansion (DX) system? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 4 What are some benefits of using a "packaged" piece of cooling equipment rather than a "split" system?
Hi please show working? Thankyou ! An air conditioner cools humid air Temperature 1 =25 celcius Temperature 2 = 10 celcius Relative humidity 1 = 70% Determine the final relative humidity (2) and calculate: 1) the energy removed 2) the water mass extracted from the air
1. An air-source heat pump is a heat-pump system that uses air: a. as the system refrigerant. b. as the heat source when operating in the cooling mode. c. as the heat sink when operating in the heating mode. d. as the heat source when operating in the heating mode. 2. According to the Department of Energy, duct leakage can result in a energy loss? a. 10% b. 20% c. 30% d. 40% 3. As the outside ambient temperature drops, the efficiency of a heat-pump system operating in the mode will: a. heating, drop b. heating, rise c. cooling, rise d. Both a and c are correct.