Identify and discuss the function of each part. Turbine Fuel Flow Meters Viscous-flow air meter

Q: The wind speed beyond which the turbine should stop its operation is triggering speed cut-in speed…

A: Cut out speed, wind speed beyond cut out speed, the turbine should stops its operation. Every wind…

Q: Describe how the wind turbine works.

A: The wind turbine as name suggests, the main energy sources comes from kinetic energy of the wind.…

Q: List five different types of oil rating systems

A: Oil Rating Systems:- The society of Automotive Engineers SAE has established a numerical code…

Q: Cross-section 4 A horizontal pipe conveys water between points, which have diameters d1 = 2548 mm…

A: Let Q= Total flow rate in the system  v1= Velocity in pipe at cross section 1 =0.922m/s p1=pressure…

Q: What determines the cut off point in performance of wind turbine

A: Turbines cut in and cut off speeds are determined by the manufacturer to protect the turbine from…

Q: A 2 inch-diameter horizontal jet of water with a velocity of 20 ft/s relative to the ground strikes…

A: Given velocity of jet of water, Vj=20 (ft/s) and the diameter of water jet, d=2 in =212 ft=0.167 ft…

Q: Why do Rocket nozzles get wider instead of smaller? (They look more like diffusers, but they are…

A: Nozzle: Nozzle is a device which increases the kinetic energy of fluid passing through it at the…

Q: two suggestions in reducing the head loss in the pump and piping syste

A: -Make the surface of the pipe is smooth so that no friction is present in the piping system so this…

Q: ration i

A: given: Methods for treating vibration in pumps

Q: Explain briefly 1. Valve lead 2. Intake lead 3. Exhaust lead

A: Valve lead The lead or valve lead is the angle of the crank shaft in which exhaust and intake valves…

Q: Match the fluid power system with its suitable applications/lequipment Hydraulics A. Dump trucks v…

A:

Q: A venturi meter is used to measure velocity for varying pressure head Select one: True False

A:

Q: True or False? Oil pressure is determined bywhether the pump is a gear type or rotor typeand by oil…

A: Given Data : Oil Pressure

Q: Which of the following flow meters is not suitable for very low flow rate? magnetic paddle wheel…

A: Given Flow meters To find Determine the flow meter among the option which are not suitable for very…

Q: The centrifugal compressors are used to produce low flow rates Select one: True False

A: Centrifugal compressor: It is a mechanical device which is use to compress the fluid (air,…

Q: 30 60° 8 ft 4 ft y cos 60° c.p. YIRVIAYIK a) Determine the total hydrostatic force of an inclined…

A: Pressure is defined as the intensity of force acting over a unit area. The pressure exerted by the…

Q: To compute the friction factors, you are assuming that the only losses in the system are due to…

A: Whenever fluid flow through the pipes there is always some kind of head loss is happened due to the…

Q: Which of the following is normally used for controlled draining of a tank? Orifice Nozzle…

A: Explanation  Orifice: Orifice is normally used for controlled draining of water . It is also used…

Q: Describe the operating principle of a Karman Vortex air flow meter used in some engine management…

A: A Karman vortex air flow meter (KVAFM) uses the principle of vortex shedding to measure the flow…

Q: Choose correct answer: Which one of the following devices creates only flow? An external gear…

A: External gear pumps are  used for pumping water and other fluids. They are preferred in applications…

Q: Compressed air can be used to clean the machine, is a general safety precaution while working in a…

A: It is important to follow the safety guidelines while working in a workshop. They are provided in…

Q: Which of the following flow meters is of positive displacement type? mass gas flow meter rotameter O…

A: Positive Displacement Meter: In this type of flow meter, the fluid mechanically displaces the…

Q: hich of the following could not be the power coefficient of a slow speed wind turbine? a. 0.444 b.…

A: Power coefficient is defined as the measurement of the efficiency of the wind turbine. It varies…

Q: mass flow rate of the air (Ibm/s).

A: Given: For a compressor Pressure at inlet (P1) = 150 psi =21600 lbf/ft2 specific volume at inlet…

Q: Description and uses of Water turbine test bed

A: Water Turbine Test Bed: Description: The test bed of water turbine plays an important role in the…

Q: pressure from the indicator diagram using a  planimeter? 6.) Besides from planimeter what other way…

A:

Q: What is the unit of flow rate?

A: Flow Rate The flow rate or discharge is defined as the volume of fluid passing through a cross…

Q: iscuss the process of using each equipment to evaluate the performance of an internal combustion…

A: 1.Turbine fuel flow meters Turbine flow metres, also known as impeller flow metres, are velocity…

Q: The total pressure rise in a centrifugal compressor is due to impeller and diffuser action Select…

A: The fluid flowing through the impeller of the centrifugal compressors are imparted kinetic energy…

Q: Why are ball valves not as useful for throttling flow other as other valves types?

A: TO ELOBRATE :- Why are ball valves not as useful for throttling flow  as other valves?

Q: turbine

A: To find ; Number of revolutions of a wind turbine.

Q: Surveyor's measuring rods in 3 or 5 m length are as shown in Figure 1. There is a choice of two push…

A:

Q: Describe working principle of pressure-compensated flow control valve

A: Pressure-compensated flow control valves are used to maintain a constant speed of operation of a…

Q: List out the applications of compressed air used in oil and gas industries

A: To find:  applications of compressed air used in oil and gas industries