IDENTIFY:A._is the center-to-center distance between bolt lines perpendicular to theaxis of the member.It is a sharp reduction in the cross section of a member that take place justВ.before the member fractures.This refers to a certain heavy W sections with flange thickness exceeding 2C. inches.is the center-to-center distance of bolts in a direction parallel to the axis ofD.the member.

Answered: Image /qna-images/answer/3a58bf74-59b5-4c18-9cb1-2de5de645b99.jpg

IDENTIFY: A. axis of the member. R It is a sharp reduction in the cross section of a member that take place just before the member fractures. This refers to a certain heavy W sections with flange thickness exceeding 2 _is the center-to-center distance between bolt lines perpendicular to the C. inches. _is the center-to-center distance of bolts in a direction parallel to the axis of D. the member.

IDENTIFY: A. axis of the member. R It is a sharp reduction in the cross section of a member that take place just before the member fractures. This refers to a certain heavy W sections with flange thickness exceeding 2 _is the center-to-center distance between bolt lines perpendicular to the C. inches. _is the center-to-center distance of bolts in a direction parallel to the axis of D. the member.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel Design Compute the net area of each of the given members
SITUATION I A lapped bolted lension member is shown. Diameter of bolts are 22 mm and the plate material is A36 steel Fy = 275 MPа, Fи 3 415 МPа. Assume the fasteners are adequate and do not control the tensile capacity. Diameter of hole is 2.5 mm bigger than the diameter of bolt. 12 :: 350 50 100 100 50 50 1. Determine the tensile capacity of the lapped joint based on gross area. a. 252.656 kN c. 866.250 kN b. 202.125 kN d. 693.000 kN 2. Determine the net Area for the tensile capacity of the lapped joint. а. 3318 тm? c. 5250 mm? b. 1554 mm? d. 1824 mm? 3. Determine the tensile capacity of the lapped joint based on the net area. a. 752.856 kN C. 866.250 kN b. 688.845 kN d. 1039.500 kN
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
Please show solutions on how to get the 0.250 value. The circle green in the figure. Civil engineering- steel design
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
5 please help meee
Determine the LRFD design strength and the ASD allowable strength . Neglect block shear. A36 steel and 3/4-in Ø bolts
1
SITUATION B. strength and the allowable strength considering the following members. Analyze the members separately except for No.7. 5. 6. Given the connection below bolted with M22 bolts, solve for the design tensile A992 W360x122 A36 L152X102X14.3 7. Built-up Section with Ey=345 MPa and Fu=450 MPa W 360 X 122 75 100 mm 100 -P L152X102X14.3 bf/2