IAIH, Fectangular plate shown in Figure (6.25) is subjected to a uniform biaxial state of stress (Ox, Oy). All other components of stress are zero. The initial dimensions of the plate are Lx-4 in. and Ly-2 in., but after the loading is applied, the dimensions are L = 4.00176 in., and L = 2.00344 in. If it is known that o, and E-10x10 ksi, (a) what is the value of Poisson's ratio? (b) What is the value of o,? 10 ksi |3D %3D

IAIH, Fectangular plate shown in Figure (6.25) is subjected to a uniform biaxial state of stress (Ox, Oy). All other components of stress are zero. The initial dimensions of the plate are Lx-4 in. and Ly-2 in., but after the loading is applied, the dimensions are L = 4.00176 in., and L = 2.00344 in. If it is known that o, and E-10x10 ksi, (a) what is the value of Poisson's ratio? (b) What is the value of o,? 10 ksi |3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calcuate Torsion From Point A to Point C and Bending from Point A to Point B and from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
A large thin rectangular plate is subjected to certain traction boundary conditions on its thin edges. The following stress function is proposed for this problem: 2 p(x,y) = A x¹ + B x²y² + Cy² (i) use the biharmonic equation to find restrictions, if any, on values of A, B, and C (ii) calculate all stress components (iii) calculate all strain components in terms of A, B, and C as well as the Young modulus and Poisson's ratio E and y, respectively. (iv) check that the equilibrium equations are satisfied (v) determine the traction boundary conditions at x=+a and y=+b
A strain element is given in the figure. Find the planes in which the normal stresses are equal in absolute value to the shear stresses.
1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N. The wire is made of a copper alloy having a stress- strain relationship that may be described mathemat- ically by 124,020ɛ 0 s8s 0.03 (o = MPa) 1+ 300ɛ in which e is nondimensional and o has units of MPa. (a) Construct a stress-strain diagram for the material. (b) Determine the elongation of the wire due to the forces P. (c) If the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Q5: At a point in a strained material the stresses acting on planes at right angles to each other are o, 30, MN/m² tensile, together with associated shear stresses which assumed clockwise in effect on oy plane. If the maximum principal stress is limited to 1002 MN/m² tensile, and xy-60 MN/m², calculate: (a) the magnitude of the o, and oy; (b) the values of the maximum and minimum principal stresses; (c) the directions of the principal planes; (d) the maximum shear stress.
The state of stress at a point in a machine component is given by ox = 120 MPa, oy = 55 MPa, Oz = -85 MPa, Oxy = -55 MPa, Oxz = -75 MPa, and oyz = 33 MPa. Construct the Mohr's circles of stress for this stress state and find the maximum shear stress.
The axially aligned pressure vessel, shown in Fig Q2, is made from aluminium exhibiting a Young's Modulus of 73GPa and a Poisson ratio of 0.34. It has an outer diameter D, of 86mm and a wall thickness t of 5mm. The vessel is subject to an internal pressure P of 150bar and externally applied torque T of 4.5kNm. a) Draw the 2D planar state of stress of any finite element located on the outer surface of the pressure vessel, according to the polar coordinate system provided. b) Sketch the longitudinal, circumferential and planar shear strain profile through the thickness of the vessel wall. c) Determine the minimum factor of safety for the given load cases, assuming the aluminium has a yield strength of 175MPA, and comment on the most likely mode and locus of failure. theta i. - Z - T Do Section A-A: Side View End View
The following stress condition is applied to a cubic material.Normal stress in the x direction is 15 Mpa, normal stress in the z direction is -7 Mpa and the shear stress in the x-z plane is 59 Mpa.(a) Write the stress tensor(b) Find the maximum normal stress(c) Find the angle with respect to the x- axis at which the maximum normal stress is applied(d) Find the maximum shear stress(e) Determine the angle with respect to the x-axis at which the maximum shear stress is experienced
Consider a circular plate that has a uniform pressure along the top surface and a fixed support on the edge around the perimeter, as shown. What would be the most efficient model to use to analyze the stress in the plate? O 3D model O Shell model O Plane stress model O Axisymmetric model TTTTT 7777
Grandpa/Shutterstock.com 7.3-26 An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of σ = -45 MPa and 7xy = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress o,. (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element. PROBLEM 7.3-26 T P o, Т 139 MPa 45 MPa
The state of stress at a point in a structure is shown in the following figure.(a) find the main stresses (Show the results on a sketch ofcorrectly oriented).(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: -all 3 principle stresses, the max in plane stress, average noemal stress and the absolut max shear stress. - Show the principle stress, the max inplane shear stress and the average normal stress on an appropriate schematic