(i) State whether the frame is in statistically stable equilibrium, and why? (ii) Determine the largest tensile and compressive force anywhere in the frame for this load (by using the method of joints or the method of section ) (ii) If all members have a cross-sectional area of 4000 mm2 and a Young's modulus of 200 GPa, by how much will these two members change in length due to the applied force? 100 kN 5 m 100 kN 20m (4 x 5m)

(i) State whether the frame is in statistically stable equilibrium, and why? (ii) Determine the largest tensile and compressive force anywhere in the frame for this load (by using the method of joints or the method of section ) (ii) If all members have a cross-sectional area of 4000 mm2 and a Young's modulus of 200 GPa, by how much will these two members change in length due to the applied force? 100 kN 5 m 100 kN 20m (4 x 5m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm2. The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. Find the magnitude P of the largest additional vertical force that can be applied to the bar.___________kN in 2 decimal places Take note: Write it on a paper, hand written showing correct answer.
A thin walled member of 1000 mm long has the cross-section shown in figure. Determine the maximum torque which can be carried by a section if the angle of twist is limited to 10%. What will be the maximum shear stress when this maximum torque is applied? Take G = 80 GPa. 18 mm- 2 mm 40 mm-
For the plane truss shown below loaded with a 200 kN force, determine the amount of deformation in membes (AB) & (AD) if their cross- sectional areas are known to be AB= 2500 mm² & AAD = 2000 mm² (assume E 200 GPa) 4 m B D 200 KN 2.5 m
4.48 A thin rod of 10 mm diameter is subjected to a tensile force of 7850 N. What are the principal: stresses and maximum shear stress? (a) 70 MPa, 50 MPa, 10 MPa (b) 100 MPa, zero, 50 MPa (c) 100 MPa, 50 MPa, 25 MPa (d) 100 MPa, zero, zero
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
to the direction of loading. When When solving for Normal/Axial/Compressive/Tensile Stress we look at an area of our member that is solving for basic Shear Stress we look at an area to the direction of loading. This is because of how the members will fail in either situation and what resists that failure. Parallel, Parallel 1000 Parallel, Perpendicular Perpendicular, Parallel Perpendicular, Perpendicular
Problem 2. [Concepts: Internal forces in 2D and average normal stress] The bars of the truss each have a cross-sectional area of 1.25 in². a) Determine the average normal stress in each member due to the loading P = 8 kip. State whether the stress is tensile or compressive. b) If the maximum average normal stress in any bar is not to exceed 20 ksi, determine the maximum magnitude P of the loads that can be applied to the truss. 4 ft 4 ft 4 E 0.75 P 0
We are given the statically indeterminate structure shown in Figure 2. Apart from the loadings, member AB is also subjected to temperature effects. The cross-sectional depth of member AB is h = 12 in, and the thermal coefficient is aT= 5:10-6 /° F. We are also given that the effect of axial forces on the deformations can be NEGLECTED. 1 kip/ft 5 kip BV VVvvvwwW EI = 8:105 kip-ft2 EI = 106 kip-ft2 20 ft Figure 2 a) Establish a primary structure b) Establish the compatibility equation from which you will obtain the redundant force c) Determine the support reactions of the structure d) Determine the internal loading diagrams of the structure e) Determine the support reactions IF THE STRUCTURE IS ONLY SUBJECTED TO THE TEMPERATURE EFFECTS (and not the loads) AT: = 5 °F ÅT;= -5 °Fi
Is it TRUE OR FALSE? 1. To analyze a statically indeterminate structure, an estimate of the member sizes must be made before the structure can be analyzed using an exact method. This is necessary because the analysis of a statically indeterminate structure is based on the elastic properties of the members. An approximate analysis of the structure will yield forces from which reasonable good initial estimates can be made of member sizes. If false why? Topic: Structural Analysis
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
B) The free ends of two cantilever beams each of length L and flexural rigidity El are joined together with a spring as shown in Fig. (6). The stiffness of the spring is K = Using the method of consistent deformations, determine the force in the spring due to a concentrated load W acting at center of the lower cantilever. www
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.