(i) In Fig.(a), calculate the load current, load voltage, load power, diode power, and total power.Assume that the diode is ideal.RL470 2RL1 kΩ+VsVsI,20 V12 V(a)(b)(ii) In Fig.(a), calculate the load current, load voltage, load power, diode power, and totalpower. Assume that the diode is real and apply the second approximation(iii) In Fig.a, calculate the load current, load voltage, load power, diode power, and totalAssume that the diode is real and apply the third approximation (RB = 0.23 Q)power.(iv) In Fig.a, If the resistor is doubled, what is the load current, load voltage, loadpower, and total power?. Assume that the diode is ideal.power,diode(v) Repeat the above problems (i) (ii) (iii) (iv) with Fig.(b)(vi)A doped semiconductor has 10 billion silicon atoms and 5 million trivalent atoms. If theambient temperature is 25°C, how many holes and free electrons are there inside thesemiconductor?

Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Answered: (i) In Fig.(a), calculate the load…

(i) In Fig.(a), calculate the load current, load voltage, load power, diode power, and total power. Assume that the diode is ideal. RL 470 2 RL 1 k2 + Vs Vs 20 V I, 12 V (a) (b)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 1. A forward bias of 0.7 V causes a current of 2mA to flow through a diode. What is the reverse…

A: Diode is a two-terminal semiconductor device that allows current to flow in one direction only. It…

Q: From the diode circuit shown below, If E=30 V and RL=402, determine the current supplied from the…

Q: 15 In the circuit shown, determine the current flowing through the resistor R1. * R2 1K R1 5V D2 1K

A: The solution is given below

Q: 5 نقاط Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages…

A: The given circuit is All the diodes are given as ideal diodes.

Q: the voltage regulator circuit shown below the power rating of Zener diode is 400 mW. The value of RL…

A: Zener diode is heavily doped semiconductor that conduct in forward and reverse direction In forward…

Q: H.W2 The single-phase half wave rectifier has R-L load with R= 50 and L= 6.5mH. The input voltage V,…

A: Given R-L load with R= 5 ohms and L= 6.5 mH. The input voltage Vs = 220 V at 50 Hz

Q: In the circuit shown below, find the diode voltage VD and the supply voltage V such that the current…

A: The threshold voltage and current flowing through the diode is given. The resistance of the diode is…

Q: Q1/ a- Using the characteristics of Figure below, determine Ip, Vp, VR for the following circuit:

Q: One of the following statements is correct regarding the photo-diode: Select one: a. The internal…

A: We need to tell that which one of the following statement is correct regarding the photo-diode: a.…

Q: R I2. 3 V 0,7 V 370 V. For the diode in the given circuit, the desired ones are obtained using the…

A: Given: Is=10-12AVT=25mVn=1 Circuit diagram

Q: 3. In the circuit shown below, the knee current of the ideal Zener diode is 10 mA. To maintain 5 V…

A: In the voltage regulator circuit. Find the minimum value of the load resistance? Maximum power…

Q: 2-5 FULL-WAVE RECTIFIERS 1. Consider the circuit in the figure. (a) What type of circuit is this?…

A: Rectifier circuit are used to convert Alternating AC into pulsating DC.it can be controlled as well…

Q: For each of the circuits given below, assume an ideal diode. For which of the following circuits is…

A: In the given questions we need to calculate the voltage across diode D2.

Q: 4) Forward bias and reverse bias are two important characteristics of the diode, how does the diode…

A: When the external voltage is applied across the P-N junction diode, this is known as forward bias or…

Q: R = 4.7 kQ www + Vp + + 5 V3

A: Need to fine Vd and V and power dissipated

Q: Question 1: For the circuit shown Di and Dz are identical having n =1 and Is =1024 A. Find the…

A: Given: Brief description: In the above given question we have an electrical circuit having…

Q: Diode Models. For the following series or parallel diode configurations, solve for the diode current…

Q: A germanium diode is connected to a load resistance of 1.5 kQ and is supplied with 12-V such that…

Q: 4) Please determine the following parameters according to the zener diode circuit which is given…

Q: a) List the main factor in determining the value of the reverse saturation current in the diode.…

A: a) Answer: Temperature (and minority charge carriers concentration)

Q: constant-voltage model (VD,on= 0.8 V) to determine the current ID flowing through the

A: Given data, VG=5 VR1=1 kΩR2=2 kΩVD,on=0.8 V By using the constant voltage model, a diode circuit is…

Q: NAnsver all the questions (1) The rms value of the input voltage for a bridge network is shown in…

A: We need to analyse the given diode network

Q: 5. Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is…

Q: For the diode circuit shown below, assuming the ON/OFF model with constant voltage drop of 0.5 V,…

A: Solution: From the OC test, we get: From our above circuit we…

Q: Let: Vi = 25 V, RS = 250 Ohm, VZ = 12V, PZmax = 450mW A. Determine VL, IL, IZ and IR If RL = 420 Ohm…

Q: 5V 100 Ohm b. 3V 100 Ohm From the figure, assume the diode to be ideal, what is the voltage across…

Q: a on junction diode is dissipating 0.5 W. If 5 V is applied across the diode( fb), then what is the…

A: The power dissipated is the product of the voltage applied across the diode and current flowing…

Q: Determine the forward voltage and + V, - forward current for the diode in the R1 Ej = 10 V oV 4.7 k2…

Q: For the diode circuits shown below, find the values of I1, I2 and V indicated. a) Using the…

Q: Find the steady-state error of this system when a unit-ramp input is applied. R(s) 1 C(s) S + 9…

A: Steady state error

Q: Plot the input/output characteristics of the circuits shown below using both ideal diode mode and…

A: Given For ideal diode , VD,on=0 V For constant voltage model ,VD,on=0.8 V R1=2 kΩ R2=5 kΩ VB= 1.8 V

Q: 1- Write the relationship between a DC and ß DC in Transistor.

A: Note: From the guidelines of the company which can solve only first question please repost the…

Q: For the circuit shown, for what range of Vi(t) will the diode be off. 1k2 D Vk 0.7V Vi(t) 1k2 Vout…

A: we need to identify the range for which diode to be off

Q: a. The Current supplied by battery is p. The Voltage across Load resistance RL is The Voltage across…

A: To solve the above problem, one should know what a three phase semi converter is, and how it works.…

Q: The current and voltage characteristics of the Diode and the Zenner diode in the circuit in Figure 1…

A: Here we will check at different values of v , wheather diode are on or off , according the output…

Q: Assuming an ideal diode, sketch Vị , Va and ia for the half-wave rectifier below. TI input is…

A: Rectifiers circuits are used to convert Alternating source to pulsating DC. It can be controlled as…

Q: Draw the circuit diagrams of a p-n junction diode in Forward bias and Reverse bias. Draw the I-V…

A: p-n junction diode in forward bias: The cycle by which, a p-n intersection diode permits the…

Q: Determine the điode's voltoge ond current for the igure VO for each of Si the diode's model. Find…

A: Given: In the above given question they have mentioned an electrical circuit having independent…

Q: Determine the range of V; that will maintain V₁ at 8V and not exceed the maximum power rating of the…

Question

(i) In Fig.(a), calculate the load current, load voltage, load power, diode power, and total power.
Assume that the diode is ideal.
RL
470 2
RL
1 kΩ
+
Vs
Vs
I,
20 V
12 V
(a)
(b)
(ii) In Fig.(a), calculate the load current, load voltage, load power, diode power, and total
power. Assume that the diode is real and apply the second approximation
(iii) In Fig.a, calculate the load current, load voltage, load power, diode power, and total
Assume that the diode is real and apply the third approximation (RB = 0.23 Q)
power.
(iv) In Fig.a, If the resistor is doubled, what is the load current, load voltage, load
power, and total power?. Assume that the diode is ideal.
power,
diode
(v) Repeat the above problems (i) (ii) (iii) (iv) with Fig.(b)
(vi)A doped semiconductor has 10 billion silicon atoms and 5 million trivalent atoms. If the
ambient temperature is 25°C, how many holes and free electrons are there inside the
semiconductor?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In this Zener diode regulator, the source voltage varies from 6 V to 11 V. Assume that the load current varies between 2 mA and 48 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Please answer in typing format solution please only typing format solution please
Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and i, Ideal -2 V 2.2 ka 6.8 k
I don't know what will be the figure of example 2. Please help. Thank you.
U3: A.C. voltage with peak value (Vm 20V) is connected in series with silicon diode an and load (R-500 £1) If the resistance of the diode-10 12, calculate: www -20V+ (1) diode current (2) output voltage Repeat (1&2) if the diode is to be ideal. +20V 500 n -20V
The diode has a forward voltage of 0.7 V. V is a variable DC source, R1 = 11KQ and R2 = 6KQ. in R1 Vin R2 V out If V, is increased from zero, at what value of V, in volts will the diode start to conduct? in
Hey, I need the answers to these questions. It's urgent.
can you solve this? Please write well
From the diode circuit shown below, If E=30 V and RL=802, determine the current supplied from the battery, the voltage across the load resistance, and the voltage across diode D2 if all the diodes are silicon with an internal resistance of 1 2. D . RL D4 D3 a. The Current supplied by battery is b. The Voltage across Load resistance RL is c. The Voltage across diode D2 is
Help me please with the waveforms for example 5. Thank you. And a bit of explanation will be much appreciated. <3
5. Assuming an ideal diode, sketch Vị, Va and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and i, Ideal V-2 V 2.2 ka R26.8 ka
Calculate the current (I) through the diode and voltage across the resistor (Vout). Assume V1 =15V,R1=6KN. Ge Vout V1 R1 Diode D1 is ON or OFF? Choose... Vout= Choose... Current (I) = Choose... v
For the subsequent questions, please refer to the circuit below. Assume that the diode is ideal (e.g. the voltage across it is zero volts when it is ON) IK VINZI IN=IV (+) I Sv(t Jo Vo Suppose we assume the diode is ON, what is V. in volts? Suppose we assume the diode is ON, what is the resistor current I in mA? Suppose we assume the diode is ON, our assumption is correct because the condition ID>=0 will hold as lp will be (in mA)... Suppose we assume the diode is OFF, this is a wrong assumption because when we solve for Vp with the diode as an open-circuit, the condition VD<=0 will NOT hold as Vp will be (in volts)...