(i) (ii) Explain sinusoidal-pulse modulation as used in PWM inverters. Discuss the conditions under which the number of pulses generated per half cycle are 40 or (-1). Here fe and f are thefrequencies of carrier and reference signals respectively. For a single-pulse modulation used in inverters, show that output voltage can be expressed as Vo = Σ 4V, na n = 1, 3, 5 na sin sin nd sin nwt 2 where 2d is the pulse width. (iii) A single-phase full bridge inverter has rms value of the fundamental component of output voltage, with single-pulse modulation, equal to 110 V. Compute the pulse width required and the rms value of output voltage in case de source volt age is 220 V.

(i) (ii) Explain sinusoidal-pulse modulation as used in PWM inverters. Discuss the conditions under which the number of pulses generated per half cycle are 40 or (-1). Here fe and f are thefrequencies of carrier and reference signals respectively. For a single-pulse modulation used in inverters, show that output voltage can be expressed as Vo = Σ 4V, na n = 1, 3, 5 na sin sin nd sin nwt 2 where 2d is the pulse width. (iii) A single-phase full bridge inverter has rms value of the fundamental component of output voltage, with single-pulse modulation, equal to 110 V. Compute the pulse width required and the rms value of output voltage in case de source volt age is 220 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An inverter circuit is shown below Vin Voo M₂ •Vout =a) if Vin = 01001110 in what is Vout (11) Draw the wave form of Vin and Vout.
B6
5c
A circuit consists of forty picofarads capacitor, NAND gate and five hundred Ohm resistor.This circuit generates clock pulses which are required to control a digital system. a)What is the frequency of the clock?(show working) b)What is the usefulfulness of the capacitor and the resistor in the drawing of the clock circuit?
A single-phase full bridge inverter is fed for a dc source such that fundamental component of output voltage is 230 V. The input frequency is 50 Hz. Find the rms value of MOSFET and diode currents if load is RLC: R=2 0, L=19 mH, and C=400 µF.
solve part (iv), let the writing easy to read pls.. thanks
7. Describe the operation principle of the MOSFETS-based digital gate shown in Figure 3. In your answer, explain the need to use n-channel and p-channel MOSFETS for such digital gates. VDD Figure 3 8. A particular optical waveguide is made from silicon with an air upper cladding and oxide lower cladding. The measured effective index of the waveguide at 1300 nm is 2.2 and the measured effective index at 1550 nm is 2.0. (a) Assuming a linear relationship between wavelength and effective index in the form of
Consider that we have a component of the full adder type, as illustrated in the figure below.Make the structural description in VHDL of an 8-bit adder using 8 components that are 1-bit full adders described as in the figure above.
27 -a wt a π-α π 2л -Vá An inverter which produces the output voltage shown the figure above is used to supply the series R (=10[Ohm]) and L(=20 [mH]) load. Determine the value of a to produce an output with an amplitude of 25 V at the fundamental frequency for the DC input voltage 125 [V] and the output frequency of 60 [Hz].
Construct an nmos circuit with depletion load with the function parameters are VDD = 5 V VTND = 0.4 V, VTNL = -0.6 V, (W/L)_L =1 Determine (W/L)_d of each transistor where output vo is 40 mv
Please show all work, thank you!
A series resonant inverter with series loaded delivers a load power of P=4000W at resonance. The load resistance is R=10 ohms. The resonant frequency is fo =20 kHz. The input voltage Vs is equal to: Select one: a. None of these b. 160.7V c. 110.1V d. 222.14V