(i) Differentiate between the mass flow and funnel flow patterns of powder flow in a hopper during discharge. A rathole may occur during the discharge of powder from a silo. Illustrate a rathole and explain how it occurs. (ii) (ii) Explain how particle size affects the flowability of powders.

Q: Density and viscosity oleic acid at 20 degree celcius and 1 atm

A: Oleic acid is an mono-unsaturated long chain fatty acid which is generally found in liquid state at…

Q: Consider a 1000 m^2 impoundment, 1 m deep. Benzene is present at 100 micrograms/L when the wind…

A: Given that, Area of impoundment, A=1000 m2  Depth, h=1 m Speed of wind over surface, u=2 m/s…

Q: Derive the Kremser equation for a stripper with three equilibrium stages

A: Kremser equation for stripping section is to be derived.

Q: Define the two types of stress waves ?

A: The two types of stress waves are to be defined.

Q: Describe the difference between average pressure and false pressure

A: The force applied perpendicular to the surface of an object per unit area over which that force is…

Q: Write the energy balance for the material in a closed container, neglecting potential and kinetic…

A: Energy conservation law states that the total energy of the system and the surroundings can neither…

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: Explain steady flow in relation to fluid mechanics.

A:

Q: Briefly explain the concept of steady state as it applies to diffusion

A: Diffusion is the process through which particles, molecules, or substances spread or travel from a…

Q: DISTILLATION PROCESS IN INDUSTRY. EXPLAIN IN DETAIL: 1-THE FLOW DIAGRAM. 2-THE BASIC SYMBOLS USED.…

A:

Q: Ex: A well is need to be drilled to 15,000 ft. The entrance into abnormal pressures at 10,000 ft are…

A:

Q: t types of ideal flow patterns in gas

A: Membranes are used in the mass transfer as a barrier in the separation processes. A membrane…

Q: B/ Define the Schmidt number, Prandtl number and Reynolds number and clear up the relation for each…

A: The Schmidt number (Sc), Prandtl number (Pr), and Reynolds number (Re) are dimensionless variables…

Q: crystallization mechanism,

A: Crystallization is a process in which mass transfer of solute takes place from the liquid solution…

Q: What is the basic equation for computing the rate of mass transfer through a membrane?

A: Consider mass transfer through a membrane of area Am takes place from one container with…

Q: Explain Process of extraction cooking oil about description and conditions process

A: Extraction is a process in which one or more components are separated selectively from a liquid or…

Q: How is compressed gas released?

A: The compressed gases are hazardous while handling as the are stored under containers in very high…

Q: Explain flow rate in relation to fluid mechanics

A:

Q: The purpose of maintaining vacuum in evaporator is to O a. Reduce in concentration O b. Reduce in…

A: Evaporation is a heat transfer process and evaporators are used to concentrate different types of…

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: Explain path line in relation to fluid mechanics.

A:

Q: 8. What type(s) of corrosion occur when metal is subjected to a high- velocity fluid flow with…

A: A) this option is not correct because it is the most general type of corrosion and is caused…

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: Why are Vertical flow-through beds preferred in RTO technology?

A: Regenerative Thermal oxidizers are used to remove air pollutants. The oxidizers will help in the…

Q: 6. In measuring the surface tension of a liquid (drop weight method), 20 drops of the liquid (r =…

A:

Q: Caking in crystals is not formed during O a. Poor flow properties of crystals O b. Open…

A: The process in which clumps or cakes are formed when crystals are stored improperly. The crystals…

Q: In chemical engineering, explain the concept of multiphase flow and its significance in various…

A: Chemical engineers use the term "multiphase flow" to describe the simultaneous movement of two or…

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: It refers to the vapor that is brought back to the column for better separation.   a Distillate…

A: In distillation we have key component as feed, distillate,residue,reflux and boilup.

Q: Which of the following does not affect the rate of liquid flow on porous media A) Type of fluid B)…

A: according to Darcy's law where Q is flow rate K is Permeability is viscosity which is dependent on…

Q: irregular shape powder

A: A particle at most basic level can be defined as a discrete portion of any substance. Particles may…

Q: Consider a colloid particle whose dimensions are 50x30x10 µm. Calculate the surface to volume…

A: Given data: Dimension of colloid particle = 50 × 30 × 10 μm

Q: Explain the concept of fluid flow and its significance in chemical engineering processes.

A: The study of fluids, which includes liquids and gases, is known as fluid flow. Fluids may flow and…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: Baffles increases the fluid velocity on the tube side. True False

A: Baffles are used to direct fluid across the tube bundle and run perpendicularly to the shell.…

Q: What is the maximum radial distance traveled by any particle in cyclone seperator?

A: Chemical processes consist of the separation stages in which the process streams are separated and…

Q: Suggest and discuss 1(ONE) example of hard materials that is suitable for improving abrasive wear…

A: Hard materials are particularly suited for challenging circumstances like ploughing, mining, rock…

Q: A mirror produces an image that is located 41.0 cm behind the mirror, when the object is located…

A: Given : The image distance, Object distance,