Answered: (i) Determine the coordinates of hole…

(i) Determine the coordinates of hole H=1 (ii) Determine the shortest distance between hole H=1 and the center (ii) Write a G code program for drilling hole H=1 only.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem 8. The piston shown is moving downward in its track at 26 cm/sec, as shown in Figure 8. All…

A: The piston shown is moving downward in its track at 26 cm/sec, as shown in Figure 8. All dimensions…

Q: For question 5, this is my way of calculate wheel A and B to find is the component will fail is…

A: Given: To find: Whether the components are safe

Q: Consider the following linear equations -7x + 8y + 4z - 7x + (25 – k)y + 3z = 11 - 7x + 8y + (7 –…

A: The given set of equations are:

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550…

A: Data given- T1 = 550 lb -ft N1 = 5000 rpm Gear ratio = 1.5/ 1 = 1.5

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0 , Y =74 , Z =…

Q: The angular velocity of AB is 8.00 rad/s lockwise in the position shown in the iagram at the right.…

A: Given, wAB= 8 rad/s

Q: please very urgent and quick

A: From the given figure,d = 122+1.52 = 12.093"O2A = 3" (K1)AB = 10" (K2)BO4 = 6" (K3)Input angle, Θ2…

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

Q: Consider FIG-DD in the appendix. Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

Q: 78. Draw a datum target area and use a datum target symbol to specify size and identify target area…

A: The datum is defined as the locus surfaces or the starting points for the location and orientation…

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: Find the number of rotations of wheel 3 in rotations per minute (rpm) wile the load A is moving down…

Q: Compute the position and orientation of the tool point P from the given D-H table for the…

A: Given: Let us consider the given table with values, and the general transformation matrix,…

Q: What is the vertical component of the velocity of point B? Let a positive velocity be up What is…

Q: 7. Point A on Link AB has a velocity of 75.0 in/s up the slot in the position shown. a) Calculate…

A: given; velocity when up the slot (VA)=75in/sAB=15inBC=10 inBD=12infor inclination vertical…

Q: Use the image below to do the following i. draw 3 positions on a piece of paper. ii. Chose a…

A: Find three positions and corresponding distances based on the reference point.Alos find linear…

Q: (i) Calculate total time taken for the cam to complete a full circle motion. (ii) Calculate the…

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Question

A flange used to connect two pipes is shown in Figure Q3. Holes need to be drilled to fix
Drilling should be done in two steps with each step 8 mm. Using absolute coordinate system
and the parameters given in the table below,
(i)
Determine the coordinates of hole H=1
(ii)
Determine the shortest distance between hole H=1 and the center
(ii)
Write a G code program for drilling hole H=1 only.
CNC Drilling Operating Conditions
Speed of the spindle
1690 RPM
Feed rate of drilling
19 mm/minute
Size of the drill bit
8 mm
Rack number of drill bit
Distance kept between the drill bit and the work piece surface 3.5 mm
The flange thickness
16 mm
H=2
H=3
H=1
B=30°
H=4
B
A = 60°.
angle
= 0°.
Center (0, 0)
Radius
= 60 mm
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

G-code

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

need help getting starting drawing this in NX? What plane
determine the number of instant centerand locate all of themusing IC Circle method.You may use a software to visualize the motion of the linkage. variable (?)=75
The "Established Datum" for number 2 and 3 are marked incorrect. Can you please help me with those two. Please refer to the image below.
The angular velocity of the next link is equal to angular velocity of previous link its own angular velocity summation of linear velocity of the previous link and its own angular velocity summation of angular velocity of the previous link and its own angular velocity
All problems will use the conventional Cartesian coordinate system unless noted otherwise. Positive x-axis points to the right, Positive y-axis points up, Angles are measured CCW (counter-clock-wise) from the positive x-axis. Problem-BB: Consider FIG-BB in the appendix. AC is a rope. BC is a rope. “C” is a steel ring. “D” is a perfect pulley. A continuous rope connects “C” to the mass. Calculate the internal forces within each rope.
1. Figure 4.11 shows a kinematic diagram of a mechanism that is driven by moving link Graphically reposition the links of the mechanism as link 2 is displaced 30° counterclockwise. Determine the resulting angular displacement of link 4 and the linear displacement of point. B 3″ AD 4.9" 90° 0 5.3" 3.3" 10.1" D 3.2"
The mechanism shown in Figure Q1 is used to feed cartons to a labeling machine and, at the same time, to prevent the stored cartons from moving down. At full speed, the driveshaft rotates clockwise with an angular velocity of 200 rpm. At the instant shown, a) Draw a configuration (Position) diagram of the mechanism. b) Graphically determine the acceleration of the ram and the angular acceleration of the connecting rod. 3" 8" 40° Ram Connecting rod Figure Q1
Can someone please help me to solve this graphically on CAD as well as analytically. Show all work thank you!
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
22 CUSTOM GENERATED PROBLEMS 3-34. Romeo tries to reach Juliet by climbing with constant velocity up a rope which is knotted at point A. Any of the three segments of the rope can sustain a maximum force of 2 kN before it breaks. Determine if Romeo, who has a mass of 65 kg, can climb the rope, and if so, can he along with his Juliet, who has a mass of 60 kg, climb down with constant velocity? ********* 60° Prob. 3-34 C Comm 2 4-2. resulta
Make sure to draw the tool path
Please help me with this Kinematics problem. This is for kinematics & dynamics of machines. Thank you.