H(z) = (z² – 0.75z + 0.5625) C = 4 and c2 = 2.). a) Sketch all possible pole-zero plots of the given system and determine the impulse response of the system for each of the mentioned possibilities. b) For one or more of the above cases is it possible to obtain a stable system? Why? For one or more of the above cases is it possible to obtain the frequency response of the given system? Why? Obtain that if it is possible. d) For which of the above cases the given system is a causal system? Explain your choice briefly. Determine the step response of the causal system. Obtain the difference equation that gives the input output relationship of the above system.

H(z) = (z² – 0.75z + 0.5625) C = 4 and c2 = 2.). a) Sketch all possible pole-zero plots of the given system and determine the impulse response of the system for each of the mentioned possibilities. b) For one or more of the above cases is it possible to obtain a stable system? Why? For one or more of the above cases is it possible to obtain the frequency response of the given system? Why? Obtain that if it is possible. d) For which of the above cases the given system is a causal system? Explain your choice briefly. Determine the step response of the causal system. Obtain the difference equation that gives the input output relationship of the above system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A signal is represented in the frequency domain by the figure below. If it is sampled at 100Hz, F(w) -50 0 50 w(rad/s) a. Sketch the sampled signal in the frequency domain. Pay attention to UNITS (5)
4+ Page 4. For two systems with impulse responses hi[n] = (0.3)" u[n] h2[n] = (0.7)" u[n] pud (a) Write down their transfer functions, H1(z) and H2(z). Include the ROCS. (b)Determine the transfer function for the parallel interconnection of these two systems. Indicate the ROC and all the poles and zeros. Plot the pole-zero diagram as well. (c)Using the result of part (b) above: Determine all possible inverse systems, H1(z). (i) Indicate which inverse is causal, and whether this inverse is stable and/or FIR? Explain. O words
Thanks
Answer with complete solutions
M2
For the pole-zero diagram shown in Figure below, the lengths of poles and zeros from the origin are 0.5 and 0.8 respectively: a. Find the transfer function H(z), impulse response h(n) and the difference equation. b. Calculate and plot the magnitude and phase frequency responses.
Q1/ for the following electric circuit drive the transfer function in (s) domain after write the differential equation for the system in the time domain. RI=2KW, R2=1.5 KW, C=3000µf. find: R2 E(t) 1. The output response of the closed loop system after supply 3.256 V as step input. 2. sketch the root locus for the open and the closed loop system. is this system stable?
+1 + R IR w VR Vs VLL V. I. -IL Consider the RLC circuit shown. The sinusoidal voltage source has a magnitude of IV 1. Answer the following questions, showing your solutions where applicable. V a. Find an expression for the complex gain, |A| 4. b. Derive an expression for the cutoff frequency/ies of the circuit. (Hint: The cutoff frequency, w is the frequency at which the output voltage is of the input voltage.) √2 c. What is the expected behavior of the output as the frequency approaches co? When the frequency approaches 0? d. At what frequency will the voltage gain be at a maximum? C
Electrical Engineering _ Power Electronics Notes: pls try to answer in less than 30 min.
+1 + R ĪR VR + + Vs I. IL Consider the RLC circuit shown. The sinusoidal voltage source has a magnitude of IV 1. Answer the following questions, showing your solutions where applicable. a. Find an expression for the complex gain, |A| (1) b. Derive an expression for the cutoff frequency/ies of the circuit. (Hint: The cutoff frequency, w, is the frequency at which the output voltage is of the input voltage.) √2 c. What is the expected behavior of the output as the frequency approaches ∞? When the frequency approaches 0? d. At what frequency will the voltage gain be at a maximum? L V C
0.1 A1 v(1) C. 3.5 A L= I mH C=01 pF Figure (Q.2.b) 2.b) Consider the circuit shown in Figure (Q.2.b) with R = 25 2. a. Compute the undamped resonant frequency, the damping coefficient, and the damping ratio ? b. The initial conditions are v(0-) = 0 and iL(0-) = 0. Show that this requires that v(0+) = 10° V/s. c. Find the particular. solution for v(t). d. Find the general solution for v(t), including the numerical values of all parameters.
Signals and system