How to draw a signal flow graph? Draw a signal flow diagram, corresponding to the state space phase-Write the state equations and the output equation for the above systemQ3Consider the system shown in Figure Q3.(a)(s+3)C(S)R(S)(s+1)(s+4)(s + 5)Figure Q3(i)considering phase-variable form.(ii)Now represent the system in state space matrix form(iii)variable form, obtained in part (ii).Bignal flow gFaph(らYsー10-20.

Answered: Image /qna-images/answer/a142a9b8-4816-4925-aed9-94a094e5ac23.jpg

Draw a signal flow diagram, corresponding to the state space phase- Write the state equations and the output equation for the above system (a) Consider the system shown in Figure Q3. Q3 (s+3) C(S) R(S) (s+)(s+4)(s + 5) Figure Q3 (i) considering phase-variable form. (ii) (iii) Draw a signal flow diagram, corresponding to the state space phase- Yarjable form, obtained in part (ii). (0)

Draw a signal flow diagram, corresponding to the state space phase- Write the state equations and the output equation for the above system (a) Consider the system shown in Figure Q3. Q3 (s+3) C(S) R(S) (s+)(s+4)(s + 5) Figure Q3 (i) considering phase-variable form. (ii) (iii) Draw a signal flow diagram, corresponding to the state space phase- Yarjable form, obtained in part (ii). (0)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A DC chopper has 225 volts as input and the output required is 425 volts. If the non-conducting time of thyristor is 225 micro seconds, compute. i) Chopping frequency. ii) If the pulse width is (1/5)th of that in case (i) for constant frequency of operation, find the new output voltage. iii) If the frequency is increased 25% of that in case (i) keeping the conducting time constant, what is the new value of k and output voltage of the chopper.
What is EMI and EMC ? How we take care in case of Electrical Hardware design?
Q4. In 1 x 4 demultiplexer, the signals given to the input and selection lines are given in the flowing figure; draw the output waveforms of the demultiplexer. Data in So
Hello. I am curious why does the MOSFET i -v characteristic "flatten out" in the saturatin region?
a) Why is a voltage-controlled current source used to model the 'active' behaviour of any Field Effect Transistor?
хх X X X ххх ххх ххх ххх 14 - x x x x x X ххх ххх x x x x x xWhat is the initial direction of the deflection of the charged particle as it enters the magnetic field shown in the figure? A) no deflection O B) into the page C) down (bottom of the page) O D) up (top of the page) out of the page
How the simulation of signal conditioning devices helps in designing them?
What are the advantages and disadvantages of 3D printed components in circuits design?
C: moving coil meter has coil resistance of (20 n ) and FSD current of ( 400 Micro amperes ). Find value of series resistance required to design a voltmeter with range of (10 volts) ,draw circuit, and find sensitivity. (: "4 bits instrumentation flash ADC" with reference voltage of 16 volts : - des - determine the maximum allowed input signal voltage. and then draw the schematic diagram of flash ADC. - the output ,when input voltage = 7 volts.
Describe Areas of Simulation Application?
What is large signal amplifier and small signal amplifier?