HW4EX1:An automobile moving over a rough road (Fig. 1.64) can be modeled considering(a) weight of the car body, passengers, seats, front wheels, and rear wheels; (b) elasticity oftires (suspension), main springs, and seats; and (c) damping of the seats, shock absorbers,and tires. Develop three mathematical models of the system using a gradual refinement in themodeling process.FIGURE 1.64 An automobile moving on arough road.EX21.5* The consequences of a head-on collision of two automobiles can be studied by consideringthe impact of the automobile on a barrier, as shown in Fig. 1.65. Construct a mathematicalmodel by considering the masses of the automobile body, engine, transmission, and suspen-sion and the elasticity of the bumpers, radiator, sheet metal body, driveline, and enginemounts.FIGURE 1.65 An automobile colliding with a barrier.

Answered: Image /qna-images/answer/8e306f4c-2181-47ad-b3ed-6c069911de5d.jpg

HW4 EX1: An automobile moving over a rough road (Fig. 1.64) can be modeled considering (a) weight of the car body, passengens, seats, front wheels, and rear wheels; (b) elasticity of tires (suspension), main springs, and seats; and (c) damping of the seats, shock absorbers, and tires. Develop three mathematical models of the system using a gradual refinement in the modeling process.

HW4 EX1: An automobile moving over a rough road (Fig. 1.64) can be modeled considering (a) weight of the car body, passengens, seats, front wheels, and rear wheels; (b) elasticity of tires (suspension), main springs, and seats; and (c) damping of the seats, shock absorbers, and tires. Develop three mathematical models of the system using a gradual refinement in the modeling process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drag force on a truck moving at a speed of 95 km/h is to be estimated using the measured data of a similar 1:10 scale model tested in a wind tunnel, Standard air is the fluid in both the prototype and the model, The truck frontal area is 10.7 m and the measured drag force on the model is 3000 N. Determine: a) the air velocity used in the wind tunnel model tests, and b) the prototype drag force in terms of the measured model drag force.
A model pump has an impeller diameter of 30 cm. During a manufacturer's test, this model achieved an efficiency of 80%. A prototype in the same family (geometrically similar) is 10 times larger than this tested model. Under the same operating conditions dynamically similar to those in the model test, what most approximately will be the efficiency of the prototype pump? O 74% OOOO O 64% O 84% O 94%
Q2/ A car wheel is supposed to be travelling at a speed of 80 mile per hour in the air. A scaled model (1:4) is tested in water instead of air and is supposed to have dynamic similarity. a) Determine the model speed in water b) then find the force ratio of the model to prototype if you know that: (pair = 1.22 kg/m³, µair = 1.78 x 10- 5 N.s/m?, Pwater 998 kg/m², µwater = 0.001 N.s/m²).
As we explained in earlier chapters, the drag force acting on a car is determined experimentally by placing the car in a wind tunnel. The drag force acting on the car is determined from where = measured drag force (N) F. C, = drag coefficient (unitless) p = air density (kg/m³) V = air speed inside the wind tunnel (m/s) A = frontal area of the car (m²) The power requirement to overcome the air resistance is computed by P = F,V Plot the power requirement (in kW) to overcome the air resistance for a car with a frontal area of 1.8 m², a drag coefficient of 0.4, and for an air density of 1.2 kg/m³. Vary the speed from zero to 120 km/h. Also, plot the rate of change of power requirement as a function of speed.
thermodynamics 1
The pressure difference ∆p produced by a water pump, and the power P required to operate it, each depend on the size of the pump, measured by the diameter D of the impeller, the volume flow rate ˙q, the rate of rotation ω, the water density ρ and dynamic viscosity µ. (a) Express the non-dimensional pressure difference and power as separate functions of the other non-dimensional groups. (b) Tests on a model pump are performed at 0.5 × full scale, at a rotation rate that is 2 × the full-scale value. To achieve dynamic similarity in the model test: (i) what would the volume flow rate of the water need to be in the model test compared to the full-scale? (ii) What would the pressure difference be compared to the full scale? (iii) What would the power consumption be relative to the full scale?
Hello..
2. Casson model was discussed in class in the context of blood rheology. This phenomenological model is often used to describe the shear stress vs. shear rate relationship in colloidal suspensions where particle aggregation might cause the measured viscosity to increase at low shear rates. In an experiment, data for the shear stress and the applied shear rate S were fitted to the Casson model written below (in a slightly different form compared to that given in the lecture notes): √t = √²₁+√as. (1) The best least square fit parameters to the experimental data were found to be 40 mPa for the yield stress to and 2.5 mPa s for the parameter a, which is referred to as the plastic viscosity. a. Using Eq. (1), derive an expression for the fluid viscosity u as a function of S. b. Plot the viscosity of the fluid as a function of S for 0.1s¹ ≤S≤ 10 s¹. c. Based on class discussion on fluid classification, how would you characterize this fluid?
A 227 kg bear* is 15 ft up a tree when it falls onto a trampoline deforming it 3 ft (where it touches the ground). Neglecting friction and mass of the trampoline (and assuming the trampoline is a simple spring), what is the spring constant of the trampoline? 1 m = 3.3 ft * the bear was OK a. 24,470.60 N/m b. 2,441.93 N/m c. 741.53 N/m d. 7,415.33 N/m
3. Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20 °C, TL=5200 °C. The density, conductivity and specific heat of the material are p 800 kg/m³, k=200 W/m.K, and cp=2500 J/kg.K, respectively. Also, r= 520 cm and L=1040cm. To TL L To
Please show working out aND explain the bukingham theorem
In the Fig. 2 below, let Ki = K2 = K and ti = t=t. %3D T -T X Fig. 2 (a) Let T= 0 °C and T= 200 °C. Solve for T: and unknown rates of heat flow in term of k and t. MEC_AMO_TEM_035_02 Page 2 of 11 Finite Element Analysis (MECH 0016.1) – Spring - 2021 -Assignment 2-QP (b) Let T- 400 °C and let fs have the prescribed value f. What are the unknowns? Solve for them in term of K, t, and f.