HW10 In an engine governor of the Porter type, the upper and lower arms are 230 mm and 330 mm respectively and pivoted on the axis of rotation. The mass of the central load is 13 kg, the mass of each ball is 1.5 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 40° and 55°, find, taking friction into account, the range of speed of the governor and Sensitiveness of Governors.

HW10 In an engine governor of the Porter type, the upper and lower arms are 230 mm and 330 mm respectively and pivoted on the axis of rotation. The mass of the central load is 13 kg, the mass of each ball is 1.5 kg and friction of the sleeve together with the resistance of the operating gear is equal to a load of 24 N at the sleeve. If the limiting inclinations of the upper arms to the vertical are 40° and 55°, find, taking friction into account, the range of speed of the governor and Sensitiveness of Governors.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the centrifugal clutch above that comprises of four ‘shoes’ symmetrically attached to the ‘spider’. Each shoe with its friction lining has a mass of 275 grams and is attached by means of a linear mechanical spring with a stiffness value of 7.5 kN/m. The coefficient of friction of the material attached to the shoes is 0.35. The centre of mass of each of the shoes is at a radius of 95 mm from the shaft centres in the rest position shown above and has a clearance distance of 9 mm to the outer drum. The outer drum has a wall thickness of 4 mm. Question 1 a. Determine the engagement speed of the centrifugal clutch. You should provide your answer in RPM (revolutions per minute) and rounded to the nearest whole value of RPM. b. Calculate the radial force acting on the clutch face when the driving shaft is rotating at a speed of 550 RPM. c. At the driving shaft speed of 550 RPM, what will be the value of torque transmitted to the driven shaft? Please note the equartions…
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
is used to control the The band brake of Fig. rotation of a drum. The coefficient of friction between the belt and the drum is 0.35 and the weight of the handle is 15 N. If a force of 200 N is applied to the end of the han- dle, determine the maximum torque for which no motion occurs if the torque is applied Clockwise. 150 mm т 200 N 60° 150 mmi 675 mm 75 mm
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
Question 3 The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant 3.1. Draw the port governor mechanism and clearly lable it. 3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
The turning moment diagram for a multicylinder engine has been drawn to a scale of 1 mm = 4550 N-m vertically and 1 mm = 2.5° horizontally. The intercepted areas between output torque curve and mean resistance line taken in order from one end are 340, -24, 245, -305, 120,-232, 228, -165 mm2, when the engine is running at 180 r.p.m. If the mass of the flywheel is 1100 kg and the total fluctuation of speed does not exceed 4% of the mean speed, find the minimum value of the radius of gyration.
The figure shows a system with a block m1 attached to a simple square thread screw with a mean diameter of 10 mm, a pitch of 3 mm and whose coefficient of static friction on the thread is 0.35. Block m1 is attached to block m2 by a rope, each of blocks m1 and m2 have a mass of 4 kg.Block m2 is in turn attached to a 15-kg block W by another rope, which passes over a static drum where the coefficient of static friction is 0.20. Determine the required Moment M that must be applied to the screw to start lifting block W. The coefficient of static friction between the surface and blocks m1 and m2 is 0.25. Need free body diagrams
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
Figure 2 В A Block A is hanging from a massless string which runs over a massless and frictionless pulley and connects to Block B. Block B slides over an inclined plane with ordinary kinetic friction. The plane under block B is inclined at an angle theta = 0 away from vertical. The other side of Block B is connected to another massless string which runs over another massless and frictionless pulley to connect to Cart C. Cart C rolls without friction over a plane which is inclined at an angle of phi = y away from vertical. C
Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner diameter of 125 mm and an outer diameter of 200 mm and the coefficient of friction between mating surfaces is 0.35. It is assumed that shafts of both machines are co-axial and the driving shaft is rotating at a constant speed of 240 rev/min when it is suddenly brought in contact with the driven shaft/machine initially rotating at 20 rev/min. The Moment of Inertia of the driven machine is 21 kgm2. A slippage period of 6.8 sec is observed while the driven machine is brought to the full speed of the driving shaft. Analyse the frictional power transmission and calculate: The magnitude of the torque necessary to cause the described acceleration of the driven shaft :
Learning Goal: To use the equations of equilibrium to analyze a system containing a wedge and to determine the necessary applied force to introduce motion into the system. The crate shown is held against wedge B by a spring. The spring is 94.0% of its original uncompressed length 1 = 3.00 m, and the spring constant is given as k = 1650 N/m. The coefficient of static friction at all contacting surfaces is μs = 0.100. The mass of the crate is m = 25.0 kg . The angle is 0 = 14.0°. Neglect the mass of the wedge. Assume the crate only moves in the y direction and that wedge A cannot move. (Figure 1) Figure B < 1 of 1 y L. Part A - Determining the normal force exerted by the crate on the wedge Determine the normal force No that the crate exerts on the wedge when the system is at rest. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) Nc= Submit P = Value Part B - Finding the smallest horizontal force P to move the crate upward Submit…