Answered: HW04-1 F = 600 lb; 120° %3D Determine…

HW04-1 F = 600 lb; 120° %3D Determine the magnitude and the direction of the resultant force act- ing on the pipe assembly. 60° F= 400 lb %3D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.4P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Related questions

Q: Determine coordinate direction angle a of the resultant force acting at A. Given that FB = 575 N and…

Q: Find the magnitude and direction of the resultant force for the system of forces shown in the…

Q: Q2/ The cable BC carries a tension of 750 N. Write this tension as a force T acting on point B in…

Q: %3D Fs=-4i +7j kN. Find the resultant force, its magnitude, and i direction with respect to the…

Q: Replace the parallel force system acting on the plate by a resultant force and specify its location…

A: Consider the equilibrium of forces in the y-direction,…

Q: Q1/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: The wall below is holding a fluid with a specific weight of 74 The wall has a gate near the lb ft³…

Q: Q1/ Determine the magnitude and direction of the resultant force in system :below P1= 10 KN P2 = 35…

A: As given that P1= 10 kN with inclination θ1= 165° ;P2=35 kN with inclination θ2=45°;P3=50 kNwithj…

Q: Q: The cable AB prevent bar OA from rotating clockwise about the pivot O. if the cable tension 750 N…

A: Given data: T = 750 N Need to determine the normal and tangential component of the tension.

Q: 2-70. The guy wires are used to support the telephone pole. Represent the force in each wire in…

A: Given Tension in wire BD = 175 N Tension in wire AC = 250 N To find Force of each wire in cartesian…

Q: Determine the direction delta of the resultant force acting on the corble measured couterclockwise…

A: F1 = 900 lbF2 = 600 lbF3 = 900 lb

Q: Determine the magnitude and direction of the resultant for system of forces shown in the figure.…

Q: Find the resultant force and direction.

Question

HW04-1
F =
= 600 lb
120°
Determine the magnitude and the
direction of the resultant force act-
ing on the pipe assembly.
60°
F=
= 400 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

* O 3l 34% À 17:50 e MENG250 - Pract.. 3 •2-33. If F, = 600 N and = 30°, determine the magnitude of the resultant force acting on the eyebolt and its direction measured clockwise from the positive x axis. 60° F2= 500 N F3 = 450 N
9a
F- 10N 250 mm The 10-N force is applied to the handle of the hy- draulic control valve as shown. Calculate the mo- 60 17.5 mm ment of this force about point O.
1.500 N/m 0750m 1.500m 275 AN 2.25 1.500m Refer to the diagram. ACD is a rigid member. Determine the magnitude of the reaction at the pint C, = kN. Determine the magnitude of the x-component of the reaction at A, Ax = N. Determine the magnitude of the y-component of the reaction at A. Ay = kN. Determine the magnitude of the resultant of the reaction at A, FA= kN.
Q2
6-72 Determine the resultant force at pins A, B. and C on the three-member frame! Hint: use segments AC and BC. Then, using the two segments, develop equations in terms of Cx and Cy. Find Cx and Cy. Then plug back in to the other equations to find the rest of the unknowns. 200 N/m 2 m 800 N 2 m
.W. Determine the res forces about point Oof the F = 500 N 0.125 m, 0.3 m- 60° 0.25 m F2= 600 N F= 300 N F,= 250 N 30 60
is 1.5 ft. Where G B. If the force vector shown below has x, y, and z components of 300 N, 400N, and 800N respectively, write it in vector form. Then determine the scalar component of the force in the unit vector direction defined by, u = 0.250i +0.968j. 5 pts Q2) 10 pts The plate is subiected to the two forces at
2/5: A cable stretched between the fixed supports A and B is under a tension T of 900 N. Determine the x and y scalar components of T, first, as a force TA acting on A and second, as a force TB acting on B. Ans. TxA = 749 N, Ty = -499 N TxB = - 749 N, Ty = 499 N 3 m 2 m 2/9: In the design of a control mechanism, it is determined that rod AB transmits a 260-N force P to the crank BC. Determine the x and y scalar components of P. Ans. Px= -240 N, Py= -100N. P = 260 N 12 B n- 30°4
Covernt from English to Metric Units and Draw FBD. Write your step by step answers.
7. The pipe assembly is subjected to the action of a wrench at B and a couple at A. Simplify this system to a resultant wrench and specify the location of the wrench along the axis of pipe CD, measured from point C. Set F=40N. 0.6 m 41 -0.8 m (60k) N 0.25 m {–40i} N B 0.25 m -Fi 0.3 m 0.3 m 0.7 m- VI-60k) N Fi 0.5 m D y
The line of action of the 3110-lb force runs through the points A and B as shown in the figure. Determine the x and y scalar components of F. A (-7, -2) Answers: Fx- Fy- y, m B (8,4) F = 3110 lb -x, m lb lb