Example 3-5: Three open-collector AND gates are connected in a wired-AND configuration as shown in Fig. 3-27.Assume that the wired-AND circuit is driving four standard TTL inputs (-1.6 mA each).(a) Write the logic expression for X.(b) Determine the minimum value of Rp if IOL(max) for each gate is 30 mA and VOL(max) is 0.4 V.+5 VSolution: (a) X=ABCDEF(b) Total current= 4(1.6 mA)=6.4 mAIRp= IOL(max)-6.4-30-6.4-23.6 mARp Vcc-VOL(mxa)//Rp 5-0.4/23.4mA=195 OhmABCHW: Show the wired-AND circuit for a 10-input AND function using74LS09 quad 2 input AND gates.DEFKARpoxFig. 3-27.

The design based on 74LS09s can be designed similar to same design with additional input functions.

Answered: HW: Show the wired-AND circuit for a…

Engineering

Electrical Engineering

HW: Show the wired-AND circuit for a 10-input AND function using 74LS09 quad 2 input AND gates.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Briefly describe what an Analog to Digital Converter (ADC) does. Consider an MCU with a reference…

A: The explanation is as follows.

Q: Q4: Make circuit diagram for 5-bit Gray-to-Binary Converter. 1 to 8 lines De-Multiplexer.

A: The 5-bit gray to binary code converter need to be designed and the 1 to 8 De-multiplexer circuit…

Q: For a certain 4-bit successive-approximation ADC, show the step-by-step conversion of a constant…

A: 4-bit successive-approximation ADC: The block diagram of a 4-bit successive-approximation ADC is…

Q: c. After sampling of analog signals, the following output conditions were observed (fs22fc),…

A: Sampling is the conversion of a continuous-time signal to a discrete-time signal in signal…

Q: Suppose there is a system consisting of temperature sensor, ADC, DAC and a Fan. The temperature…

A: Voltage range Digital o/p 0-2.5 0.0 2.5-5 0.1 5-7.5 1.0 7.5-10 1.1 If voltage is greater…

Q: Electrical Engineering. What is the function of MCB. Write two advantage and disadvantage of MCB

A: An MCB is a type of electrical switch that operates automatically to guard against overload or short…

Q: For each expression below

Q: V1 9V R1 1K D1 1N751, 5V1 VR1 5K ...

Q: For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: For the following circuit please find the small signal Input resistance in Ohms [Select] the Output…

Q: 9. For a normal operation of an n-channel JFET, how do you bias the gate source junction?…

A: JFET is a electronic device. It is abbreviated as Junction Field Effect Transistor. It is a current…

Q: Q1// Analysis the ceircuit shown in figure below. ET J2 Q2 CLH K2 REET J1 CLH K1 RESET CLK

A: Note: As per the guidelines, we experts are allowed to solve only one question. Kindly repost the…

Q: how Complete Solution. No Shortcuts. Thank you! Suppose if the signal is about 0 - 12v and we have…

A: Solution- Given, signal is about 0-12 V 16 bit ADC ⇒n= 16 ADC…

Q: The value of the current IDSS is Select one: a. the midpoint drain current b. the maximum possible…

A: In this question we will write about the current IDSS in FETs...

Q: What is the full-scale voltage of a 6-BIT binary R-2R ladder D/A converter with a 6.4 volt…

A: Given data, 6-bit binary R-2R ladder D/A converter, VR=6.4 V

Q: Arm resistances of Wheatstone bridge are,R₁ = 200 £2 R₂ = 400 2 R₁ = 500 S R₁ = 600 Input is, E5V.…

A: A wheat stone bridge with the given resistances is shown below: The bridge output voltage is given…

Q: A three- phase 13.8 kV, 60HZ, 50 km long transmission line has total impedance of 10.63+ j20.242.…

A: " Since you have posted a question with multiple subparts, we will solve the first three subparts…

Q: A force sensor was designed using a cantilever load cell and four active strain gauges. (Show that…

Q: Q4:-What is the fire angle that required to design an R-triggering circuit for a half wave…

A: In the given question we note that Igt(min) = 0.5mAVgt(min) = 0.7mAVd = 0.7VSupply voltage is…

Q: Common gate configuration What is the relation of ID and VGS to the q-point. Explain

Q: #2. In the 3-phase power system shown in Fig.2, the delta connected load is supplied through a short…

A: The three phase power system is shown below, Where,Line impedance, Zline=0.1+j5 ΩLoad impedance,…

Q: The usage of weighted resister and R-2R ladder varies based on applications. Compare the advantages…

A: Advantage of Weighted Binary DAC: Simple to construct and provides with fast conversion Advantage of…

Q: Consider a four-bit successive approximation analog to digital converter with the following…

Q: As a function of Vdd, Cvdd, and Cgnd, how much energy is pulled out of the supply voltage Vdd when…

A: CMOS stands for Complementary Metal-Oxide-Semiconductor, and it refers to a technology used in the…

Q: 5. What digital logic does the following circuit represent? Explain your answer with the analog…

A: Given:A digital logic circuit,when V1=V2=5 V (high logic), both transistors work in saturation and…

Q: output voltage for the inputs An 8-bit D/A converter has a resolution of 10 mV/bit. Find the analog…

Q: Q.2 Explain Operation of Full Converter: Fully Controlled Full wave rectifier with RLE load and also…

A: It is given the full wave controlled rectifier and given two different loads we have to elaborate…

Q: Describe the controllability and observability of a system ur detail. To check the controllability…

A: Describe the controlability and observability of the given model. State space equation are given.…

Q: Three ADCS all have a range of 0 to 10 V. What is the maximum uncertainty in the digitization of a…

A: Given Three ADCs have range of 0 to 10 v signal voltage V=10 v

Q: The RTD has an input temperature of 367oC ,and a change in resistance of 97.4ohms. The Sensitivity…

A: The RTD RTD used to measure temperature, input temperature of 367 °c change in resistance of…

Q: The RTD has an input temperature of 367oC ,and a change in resistance of 97.4ohms. The Sensitivity…

Q: 1. The diagram below shows a typical data acquisition system where an analogue signal from a…

A: Data acquisition system is used to perform some necessary operations on data. Figure shows the block…

Q: What is the function of MCB. Write two advantage and disadvantage of MCB

A: MCB An MCB is an electromechanical switch that operates automatically and is specifically designed…

Q: Q2) Derive the NOT gate and then sketch the MUX equivalen?

Q: Temperature coefficient of resistance. 3. Simplify the Boolean function below and draw the…

Question

Example 3-5: Three open-collector AND gates are connected in a wired-AND configuration as shown in Fig. 3-27.
Assume that the wired-AND circuit is driving four standard TTL inputs (-1.6 mA each).
(a) Write the logic expression for X.
(b) Determine the minimum value of Rp if IOL(max) for each gate is 30 mA and VOL(max) is 0.4 V.
+5 V
Solution: (a) X=ABCDEF
(b) Total current= 4(1.6 mA)=6.4 mA
IRp= IOL(max)-6.4-30-6.4-23.6 mA
Rp Vcc-VOL(mxa)//Rp 5-0.4/23.4mA=195 Ohm
A
B
C
HW: Show the wired-AND circuit for a 10-input AND function using
74LS09 quad 2 input AND gates.
D
E
F
K
A
Rp
ox
Fig. 3-27.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A following figure, Q1 and Q2 are identical and operate in active mode. if Ic1 = 7.5 Ic2 In then V1-V2: Ic2 V3 Select one: O a. None of these b. VT In 5 O c. VT In 10 d. VT In 1 e. VT In 7.5
Q11. to obtain NOT gate from NOR, we use A. two NOR gates O D. None of the above OC. one NOR with one input grounded OB. one NOR with shortage its inputs
Q1: Determine all the output waveforms for the 74HC195 when its input signals are shown below CLK J K SH/LD CLR Do D₁ D₂ ----- ......
Plz I need the answer of this question in digital system design
need the answer fast please
W Q.2) A Full-wave bridge rectifier with a (400 Sin(100)t) sinusoidal input has a load resistor of (10KS) .Sketch Vo and determine the : 1- Fi and Fo So 2- Vdc 2%. 〃 3- Vrms 4- Irms 5- Prms 6- Pdc PHO 7- Efficiency 8- Ripple Factor 9- PIV (.
Please answer fast I'll rate
A 5-bit ADC has the following reference values Vref= -2V and 12V. Give the value of the smallest and the largest analog values, respectively, that can be represented by the ADC.
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 12 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, de voltage and ripple factor. If the load resistance has a value of 7 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage. A01 D2 A D3 D4
Topic: Input and Output Characteristics of Transistor in Common Base Configuration Answer in 2-3 sentences each. Need a kind tutor that will do it for me. Thank you! 1. What is the range of "a" (alpha) for the transistor? 2. Identify various regions in output characteristics. 3. What is the relation of "a" (alpha) and "b" (beta)?
Which input must be active for a BCD priority encoder for its active-HIGH outputs to have the following code: a. Q3Q₂Q1Q0 = 0111 b. Q3Q2Q10 = 0001 C. Q302₂Q1Q0 = 1001 d. Q3Q2Q1Q0 = 0000
Q2: What are the types of base band digital moxdulation and explain one of its. nu tuchnioues used