HW-3-: A hall with measured length equal to (40m) and measured width equal to (30m), the standard deviation (for only one measurement) for both the length and width was equal and found to be (+0.02m). The standard deviation of the mean for both the length and width was equal as well. Calculate how many times the length and width must be measured to get (oA = +0.5 m2).

HW-3-: A hall with measured length equal to (40m) and measured width equal to (30m), the standard deviation (for only one measurement) for both the length and width was equal and found to be (+0.02m). The standard deviation of the mean for both the length and width was equal as well. Calculate how many times the length and width must be measured to get (oA = +0.5 m2).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Suppose that a = 3.24 m and b= 1.8 m. (Figure 1). Figure y=x¹/2 b 1 of 1 > X Part A Determine the moment of inertia for the shaded area about the axis. Express your answer to three significant figures and include the appropriate units. Submit 0 ■μÃ xª Xh Value a Provide Feedback A X-10 Units Previous Answers Request Answer W X X Incorrect; Try Again; 23 attempts remaining ? Next >
I need the answer quickly
Calculate the volume V of the solid generated by revolving the 65-mm right-triangular area about the z-axis through 180°. Assume a = 65 mm, b = 40 mm. a dod Answer: V = i mm³
Please help me ASAP. Please put the answer on the paper. Complete solution. I need the answer after 40 minutes. Rate will be given accordingly. Thank you in advance.Line AB was measured and the result is 745m. It is measured using a 30m tape that is0.005m tooshort. The tape is standardized at 20°C under a 4.5kg pull. During measurement the temperature is30°C under a pull of 9.57kg. What is the true horizontal distance of line AB due to incorrect tape length,temperature, and pull? The cross-sectional area of the tape is 0.05cm2 and E = 2x106 kg/cm2.
The position of a particle is given by s = 0.25t3 -0.65t²-2.80t + 5.11, where s is in feet and the time t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 11 seconds of motion. After you have the plots, answer the questions as a check on your work. -1 Questions: + + 2 0 1 When t = 0.8 sec, v = When t = 8.6 sec, v = i Mi 3 -+s, ft ft/sec, a = ft/sec, a = The positive time at which the particle changes direction is i i Mi sec. ft/sec² ft/sec²
Question- A 100 m tape weighing 30N is suspended between the two ends under a standard pull of 100 N. Find the correct distance between the tape ends. T
Q. Determine the kinematic viscosity at the average temperature and determine the Reynolds number and type of flow using the data shown below and table values: Data obatined from a Reynolds Number test: Water temperature at the beginning of the experiment = 25 oC Water temperature at the end of the experiment = 30 oC The Volume of water collected in 25 seconds = 240 ml Pipe diameter, d= 10 mm. (use eq'n reynold's number, Re = VD/v
d) The viscosity of a fluid is to be measured using a viscometer constructed of two 750 mm long concentric cylinders. The outer diameter of the inner cylinder is 150 mm and the gap between the two cylinders is 1.2 mm. The inner cylinder is rotated at 200 rpm and the torque is measured to be 10 Nm. a) Derive a generals expression for the viscosity of a fluid using this type of viscometer, and; b) Determine the viscosity of the fluid for the experiment above. Shaft е -Cylinder - Velocity Profile
Solve for the critical value of P under LRFD Method. Use Fy = 275MPA, Fu = 400MPa and thickness equal to 12mm. 80 60 60 80 60 60 80 60 mm mm 100 mm mm mm mm mm mm mm mm 80mm 180 280 160 440 250 400 60mm 400 320 360 180 280 250 60mm 100 280 140 360 20 480 80mm
Consider the shaded area shown in (Figure 1). Suppose that a = 5 in., b = 3 in., and r = 2 in. Figure y -bb- a 1 of 1 X Part A Determine the moment of inertia for the shaded area about the x axis. Express your answer to three significant figures and include the appropriate units. Iz = Submit ΜΑ Value Request Answer < Return to Assignment Units Provide Feedback ?