HW 2-2 (2): On a 100 lossless transmission line, the distance of the first minimum from the load is 2 cm, the distance of the first voltage maximum is 8 cm, and the standing wave ratio is 3. Find the load impedance in real and imaginary notation. dmax=8.cm dmin:=2.cm SWR:=3 Zo: 100.2

Q: What will be the modified form of the codeword is even parity is used: 011010

A: When parity is used, then the parity bit is added to the left-most position of the bitstream.  In…

Q: Remember to put no space in between characters. f the final ansawer is a whole number, pot no…

A: To analyze the capacitor circuit, we should understand the series/parallel, voltage division rules.…

Q: (a) Design a high-pass filter using the circuit shownto provide a loss of no more than 0.5dBathigh…

A: Given circuit is - Given values are - Cutoff frequency is 20 kHz. Given resistance chart is -…

Q: Calculate the power saving in percent for the H3E system of an AM signal modulated to 57%. Your…

A: Given: Modulation percent of the H3E system of an AM signal = 57 %. To find: Power saving in %.

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: Convert the OCTAL NUMBER 4033.347 2 to decimal number (show the steps in paper , scan and upload…

A: The octal number can be converted into decimal number directly given as:…

Q: Q-01 (What is called Buck Converter & What is called Boost Converter?)  give two examples for each.

A: Explanation: The buck converter is a ubiquitous DC-DC converter that correctly converts an excessive…

Q: Electronic What is Polymorphism. What is Mailbox.

A: The System Verilog provide dynamic array construct. In packed array one location and whole location…

Q: mostly don't know how to do question (d) and (e)

A:

Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…

A:

Q: Explain any two Data presentation Element in measurement system with neat diagrams. Note:please do…

A:

Q: When the load of a voltage multiplier is too small, __." Choices: the output voltage is unaffected…

A: Voltage multiplier is the circuit which is used to give high dc value of voltage at the output…

Q: In FET, what is the value for when Ip=lpss/2? [Approximate time to answer: 2 Minutes.] O gmo/2 O 3…

A: solve for transconductance

Q: The full form of PISO is

A: The full form of PISO is Parallel-in Serial-Out in  technology terminology PISO is acronym for lot…

Q: Did you meet at the college .A a lot of .B anybody .C few .D

A: Given: Did you meet _______ at the college

Q: What is HT supply?

A: What is HT supply?

Q: e) Convert the following Decimal numbers to Octal numbers: (79), and (159).

A:

Q: Digital communication system can handle a) Analog signals b) 1D signals c) 2D signals d) All of the…

A: The correct answer is OPTION D

Q: Measures to be taken in protecting the electronic rotection of information centers

A:

Q: Question 6: Give the preferred IUPAC name of the compound in Figure 6. [Use lowercase letters. Do…

A: The given compound is:

Q: Q) In measurement system, which of 1 point the following static characteristics are desirable? *…

A: Accuracy is the degree of closeness of the measurement and sensitivity is the how output is reacts…

Q: 5. Explain the application of DSP in mobile phones

A: DSP is known as digital signal processor these DSP are fabricated in chips which are integrated in…

Q: Q11: You are asked to calculate the amount of telephone traffic coming out of a telephone switch to…

A: For the given statement we need to choose the correct option.The given statement is "You are asked…

Q: What is the difference between blocking assignments and non- blocking assignments ? What is the…

A: Verilog is a hardware description language. The memory and array declaration in Verilog is static.…

Q: Identify and Explain with neat sketch of the 1. Pin Type Insulator 2. Suspension Type 3. Strain…

A: Pin type insulator: This type of the insulators the most early grown overhead insulator, yet are…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: Define noise in communication systems and mention the different types Note: Please do not…

A: Noise is an unwanted signal which interferes with the original message signal and corrupts the…

Q: All forms of communication have a(n)_ built into them. O A. bias O B. Mercator projection

A: Communication System- The communication system model is described as a communication exchange…

Q: can you write it in paper and use super position

A:

Q: Use block diagram formula

A:

Q: Discuss the difference between the off-line and online UPS

A:

Q: Z Look at the graph in figure 4 and complete the gaps in the text with a preposition from the box.…

A: Given  Fill in the blanks using the preposition table given. Please find the below attachment.

Q: Types of error in the measuring intrument in short.

A: There are four types of error in measuring instrument, and these given in step-2.

Q: Convert below base20 number into base3 number  (7AD)base 20 Please provide answer as soon as…

A:

Q: Remember to put no space in between characters. If the final answer is a whole number, put no…

A: Note: As per our policy, I have answered the first three subquestions. Given data: C1=2.5 FC2=1.5…

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

Q: in zeq 1 where did you get 210.949 from?

A: Student is asked to explain from where did get ZB 210.949 from?

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.