How would you hook up three resistors in a circuit to get (a) the maximum current and(b) the minimum current?A 200-2 resistor and a 500-N resistor are in series as a part of a larger circuit. If thevoltage across the 200-N resistor is 2.0 V, what is the voltage across the 500-2 resistor?If the equivalent resistance of the two resistors in series is 50-N and 12-2 if they areconnected in parallel, what are the resistances of the two resistors?Three resistors R1 = 20, R2 = 42 R3 = 82 are connected to a source with terminalvoltage of 6V. find the current that would pass through each resistor and the voltageacross each if they are connected ina. seriesb. parallel.A 40 resistor is connected in series with the parallel assembly of 3 Q and 6 Nresistors.The current through the 4 2 resistor is 6 A. What is the current through the 3 2resistor?

“Since you have asked multiple question, we will solve the first question for you. If you want any…

Answered: How would you hook up three resistors…

Science

Physics

How would you hook up three resistors in a circuit to get (a) the maximum current and (b) the minimum current?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The pedestrian crossing of Washington Road and Ivy Lane (near the Physics building) needs a back-up battery in event of power failure. In order for the three lights to be bright enough to be seen in daylight, each of the three RL = 50 N lights must dissipate P = the 3 lights are connected in parallel (see the drawing), and the open circuit voltage of the battery (that is, the voltage when there is no current) is Vo = 110 volts. What is the maximum internal battery resistance R; allowable given that each lamp must dissipate 220 watts? 220 watts. Suppose %3D %3D Ri Vo RL pyri
Problem For the circuit described by the schematic diagram below, please compute (a) the potential difference across the terminals of the 8.00 2 resistor, (b) the magnitude of the current flow through the 8.00 Q resistor, (c) the direction of the current flow through the 8.00 2 resistor, left-to-right| right-to-left Circle the correct choice and cross out the incorrect option. (d) and the power dissipated by the 8.00 2 resistor. 2.00 0 8.00 0 6.00 V 3.00 V 9.00 V >4.00 0
Two balteries with el= 3V and e2 =5V, as in the Circuit in the figure, 2i = 1D W, It is connecled to three resistors 22 =20W and 23= 30W + - 102 30 2 Using +he Kirchoff rules I, I2 ond I3 current (Eirst write volues the possing throught the resstors tind it equotions Cleorly find the currents) ithen
dv + 5v = 10B(t), dt v(0) = 0 %3D For this problem we are just going to look at the equation for the battery. A fully charged battery when connected to the circuit at time zero have a voltage source equation B(t) = 10e-0.5t %3D b. Our battery is off until one second then connects for one second, then is off for one second and does not recharge (it just retains the voltage it had when it was removed from the circuit) and then is turned on for one second, then it turned off for good. Give the function for the battery voltage in the circuit using the Heaviside function and the exponential function. B2(t) =
???
Calculate the current through each resistor. Assume that the values of the resistances are R 1= 24000 and R2 = 1400 ohms the emfs of the two batteries are e1 = 1.5 V and e2 = 3 V. (a) Write down the equation for the loop that travels through battery 1,resistor 1 and battery 2. (b) Write down the equation for the loop that travels through battery 2 and resistor R2. (c) Obtain the relation among three branch currents. (d) Calculate the values of the currents I1,12 and 13. (e) Calculate the power dissipated by each resistor. R1 R2 Is E1 A- В I E E E !!
In the figure circuit section AB absorbs energy at a rate of 55 W when current i 0.90 A through it is in the indicated direction. Resistance R = 2.0 Q. (a) What is the potential difference between A and B? Emf device X lacks internal resistance. (b) What is its emf? R (a) Number i Units (b) Number i Units
The power consumed in the circuit is 63W. Find the value of R
The capacitance in the figure circuit shown is C-0.30µF,, the total resistance is 20kΩ and the fem battery is 12 V. Determine a) the time constant b) the maximum charge that the capacitor could acquire, c) thetime it takes for the load to reach 99% of that value, d) current I when the Q load is half its value maximum, e) the maximum current and f ) the Q load when current I is 0.20 of its maximum value.
I think it’s the last choice but I’m not sure why cross sectional area plays a role
Let the resistors have resistances of R1 = 4Ω, R2 = 6Ω, R3 = 8Ω, R4 = 10Ω.Answer the following questions using Kirchoff ’s rules:(a) What is the current through R3 in a circuit where you have the battery, then thefirst two resistors (R1, R2) hooked up in series, followed by the second two resistors(R3, R4) hooked up in parallel, before reconnecting back to the battery.(Show your circuit and what you choose for the loop(s) and junction(s) as part ofyour solution).(b) What is the current through R1 if you switch R1 with R3 in your original circuit?(Show your circuit and what you choose for the loop(s) and junction(s) as part ofyour solution).(c) What is the voltage drop across R4 in part (a)?(d) What is the voltage drop across R2 in part (b)?
I have attached the question below, much appreciated